manualshive.com logo in svg

GE VR11, Справочное руководство

Поделиться
Скачать
GE VR11 Скачать руководство пользователя страница 81

Without battery and without this supply voltage, the real time clock oscillator 
has to be started at each power up. This time gets longer when operating at 
lower temperatures and can be up to around 30 seconds (at -40 °C). At normal 
ambient temperatures this delay is below one second. 
 
The red status LED goes off after the reset sequence and starts its normal 
blinking within the BIOS POST after the RTC oscillator is up. 
 
When ordering a battery-less VR11, the setup information is stored 
automatically within an onboard EEPROM and is updated via standard BIOS 
Setup function. No external software is needed to create a user defined setup 
like in earlier products from GE Intelligent Platforms. It is still recommended to 
use an external supply voltage to this battery input to avoid the power on 
oscillator start time and to keep the date and time information. 
 
 

Environment Conditions 

Ambient temperatures and humidity values for theVR11: 
 

Table 27: Environment conditions 

 

Style 1 

Style 3, 6, 8 

High Temperature 
-

 

Storage 

-

 

Operating (see diagram below) 

 
+85 °C 

 
+85 °C 

Low Temperature 
-

 

Storage 

-

 

Operating 

 
-40 °C 
0 °C 

 
-40 °C 
-40 °C 

Temperature Shock 
-

 

Storage 

-

 

Operating 

 
+/-10 °C/min 
+/-5 °C/min 

 
+/-20 °C/min 
+/-10 °C/min 

Relative Humidity 
-

 

Storage, Operating 

 
Up to 95 %, non-condensing 

VP11 only supports style 1 and 3. 
Storage temperature on style 6 & 8 is between -55 °C (low) and +105 °C 
(high). 
 
 
Shock and vibration values for the VR11 designed to meet the values listed 
below: 

Table 28: Shock & vibration parameters 

 

Style 1, 3 

Style 6 

Style 8 

Vibration 
-

 

Spectrum 

-

 

Acceleration 

 
5 to 100 Hz 
2 g 

rms

 

 
5 to 2000 Hz 
2 g 

rms

 

 
5 to 2000 Hz 
14 g 

rms

 

Shock 
-

 

Amplitude 

-

 

Duration 

 
12 g 
6 ms 

 
20 g 
6 ms 

 
40 g / 100 g 
11 ms / 6 ms 

GE Intelligent Platforms – VR11, VP11 Hardware Reference Manual, Second Edition 

Page 81

 

Содержание VR11























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды