GE Vivid S70 Скачать руководство пользователя страница 345 | Manualshive

Страница: 345 / 709

background image

4D Auto MVQ

Vivid S70 / S60

–

User Manual

8-67

BC092760-1EN

01

4D Auto MVQ

The 4D Auto MVQ (Automated Mitral Valve Quantification) tool
allows the user to perform computer assisted identification and
segmentation of 4D TEE images of the Mitral Valve (MV). Upon
completion of the segmentation the tool will provide metrics for
the MV annulus and leaflet during systole.

The 4D Auto MVQ tool is only on the Vivid S70 with 4D option
available when 4D is enabled.

Requirements

4D Auto MVQ is available on 4D trans-esophageal
echocardiographic (TEE) tissue data sets in replay mode only.

CAUTION

The results may be inaccurate when the tool is used on loops
with volume rate lower than 12 vps.

CAUTION

Do not use the 4D Auto MVQ tool if:

•

The image quality is poor.

•

The acquisition has stitching artifacts (see page 6-8 on
how to avoid stitching artifacts).

•

The acquisition has significant reverberation artifacts.

•

Any part of the valve or annulus is outside the ultrasound
sector.

CAUTION

The tool must not be used on other structures than the mitral
valve.

«
...
343
344
345
346
347
...
»

Содержание Vivid S70






































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Vivid S70

Бренд: Parker Страницы: 54

Бренд: GE Страницы: 802

Бренд: iET Страницы: 17

Бренд: C.M.O Страницы: 10

Бренд: Faderfox Страницы: 8

Бренд: Hammer Страницы: 42

Бренд: MacDon Страницы: 46

Бренд: MacDon Страницы: 82

Бренд: Mac Medical Страницы: 2

Бренд: MACDEV Страницы: 8

Mentor Touch ET750

Бренд: MAC TOOLS Страницы: 24

Бренд: MA lighting Страницы: 10

Marathon Multi600

Бренд: Saeyang Страницы: 21

Бренд: S&C Страницы: 11

Бренд: Yamaha Страницы: 45

Бренд: GE Страницы: 194

Бренд: Ekinex Страницы: 37

Бренд: HMS Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды