manualshive.com logo in svg

GE Vivid S70, Руководство пользователя

Поделиться
Скачать
GE Vivid S70 Скачать руководство пользователя страница 207

4D-Mode

Vivid S70 / S60

 – 

User Manual

6-7

BC092760-1EN

 

01

4D-Mode acquisition

Real time single beat 4D acquisition

1.  Select a 4D probe, and an application.
2.  Enter 4D either by pressing the 

4D

 button on the Control 

panel or by selecting a 4D acquisition preset on the Touch 
panel: 

Medium

 (medium size sector with top-down view), 

Large

 (large sector more suited for acquisition of the 

complete LV), or 

Bird's view

 on page 2 (small sector seen 

from the side).

NOTE: 

4D acquisition may also be done in Multi-Slice mode 
(‘Multi-Slice acquisition’ on page 6-10) and 4D Zoom 
prepare mode (‘4D Zoom prepare acquisition’ on 
page 6-13).

The volume acquisition is started.

3.  The following parameters may be adjusted during 

acquisition:
• 

Volume size

: adjust the volume size. An increase of the 

volume size will reduce the volume rate.

• 

Volume shape

: adjust the ratio between the elevation 

and azimuth widths. Changing the volume shape from 
default will increase the volume rate.

• 

Frame rate

: adjust the frame rate. There is a trade-off 

between the frame rate and the image quality.

• 

Elevation tilt

: tilt the volume in the elevation plane and 

change the viewing direction accordingly.

• 

Other parameters: Frequency and Octave.

• 

Angle

: display different rendering views.

• 

Layout

: display different layout alternatives.

4.  Optimize the image quality as necessary (2D Gain, 4D Gain, 

Volume Optimize and UD Clarity).
• 

If desired, select a 

Color map

 to colorize the volume 

rendering. The Depth color maps use a combination of 
colors to improve depth perception.

Press 

Red

 or 

Color Laser lines

 on the Touch panel 

(page 2) to visualize the 2D image locations in the volume 
rendering. The 2D image locations are shown as overlaying 
red or color coded lines following the surface in the volume 
rendering. The color of the laser lines corresponds to the 
color coding used for the 2D images.

5.  Press 

Store

 to store the acquisition.

Содержание Vivid S70






































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды