Specification Created 6/04
350355
GSD5900G – GE Built-In Dishwasher
GE Appliances
24
25-3/4
MAX.
21-1/2
3-1/4
4 (Adjustable)
34 MIN.
adj. to 35
24-3/4
23-3/8
Built-In Dishwasher Dimensions
(in inches)
Electrical Rating
Voltage AC . . . . . . . . . . . . . . . . . . . . . . 120
Hertz . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Total connected load amperage . . . . . 8.2
Calrod
®
heater watts max. . . . . . . . . . 725
For use on adequately wired 120-volt,
15-amp circuit having 2-wire service with
a separate ground wire. This appliance
must be grounded for safe operation.
Dishwasher Rough-In Information
Note:
Dishwasher must not be installed more than 10 feet
from sink for proper drainage. All plumbing and electrical work
must be in accordance with local codes.
Note:
If a flush look is needed, a 25" base cabinet needs
to be used.
The power cord and connections must comply with the
National Electrical Code Section 422 and/or local codes and
ordinances. The cord must be no longer than 6 ft. from the
junction box to the receptacle.
Installation Information
(in inches)
This wall area
must be free of
pipes or wires
Countertop
4
6
Hot
water
line on
left
4
4
2
Plumbing and electrical
service must enter
inside shaded area
24" From wall
24" MIN.
90°
19" MIN. from wall
24"
MIN.
6
34-1/2±1/4"
Underside
of countertop
to floor
5
5
90°
Electrical
wiring on
right
Electrical
wiring is
3" from
cabinet
White (neutral)
Black (line)
Ground
For answers to your Monogram,
®
GE Profile
™
or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center
®
service, 800.626.2000.
R
Listed by
Underwriters
Laboratories
Wood Insert Cut-Out Dimensions
(flat door models only)
C
B
Access insert
Detail D
Panel Thickness
Door insert
Front
of
Panel
Dishwashers Installation
(Pub. 1-G003 pg. 131B) May 12, 1993
Wood Insert Cut-Out Dimensions (in inches)
GE/Hotpoint/RCA
A
1-1/2
1/2
When using GPF325
1/4" custom dishwasher
door and access panel kit.
When using GPF375
3/4" custom dishwasher
door and access panel kit.
1/4
3/4
C
B
Access insert
Detail D
Panel Thickness
Door insert
Front
of
Panel
Dishwashers Installation
(Pub. 1-G003 pg. 131B) May 12, 1993
Wood Insert Cut-Out Dimensions (in inches)
GE/Hotpoint/RCA
A
1-1/2
1/2
When using GPF325
1/4" custom dishwasher
door and access panel kit.
When using GPF375
3/4" custom dishwasher
door and access panel kit.
1/4
3/4
Side View
GPF475 only:
Detail
D
As an ENERGY STAR
®
partner, GE has determined
that this product meets the
ENERGY STAR guidelines
for energy efficiency.
Kit
A
B
C
D – Panel
Thickness
GPF425
19-3/4"
23-9/16"
3-11/16"
1/4"
GPF475
19-97/8"
23-5/8"
3-11/16" to
34-1/4"**
3/4"
*
* Bottom of panel must be notched 1-1/2" x 1/2" to clear
access panel. (See illustration above)
** Adjustment required to match adjacent cabinet fronts due
to leveling adjustment, 4" nominal.
