GE TMO2D Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 102

background image

Chapter 5. Advanced Programming

58

TMO2D Digital Display User’s Manual

5.7 Response Parameters? (cont.)

The next setting, Tau (down), is the tau value for calculations while the measured gas concentration is decreasing.
Increasing the Tau (down) reading increases the transmitter’s response speed.

5.8 LabCal Outputs?

The

LabCal Outputs?

option enables you to calibrate (or trim) the analog outputs. After you select the output (A or B)

to calibrate, the output is driven to 20 mA. You can input the actual output value (as shown by a multimeter or
connected control device) and adjust the output. The output is then driven to 4 mA, and you can make a similar
adjustment.

FACTORY SETUP MENU
Tau (down) [XX.XX]:

Use the numeric keys to enter the desired value. Press [YES] to enter the number,
and [YES] again to confirm the entry.

FACTORY SETUP MENU
Thresh (%) [XX.XX]:

Use the numeric keys to enter the desired value. Press [YES] to enter the number,
and [YES] again to confirm the entry.

FACTORY SETUP MENU
Smooth (%) [XX.XX]:

Use the numeric keys to enter the desired value. Press [YES] to enter the number,
and [YES] again to confirm the entry.

FACTORY SETUP MENU
Window (%) [XX.XX]:

Use the numeric keys to enter the desired value. Press [YES] to enter the number,
and [YES] again to confirm the entry.

FACTORY SETUP MENU
Response Parameters?

Press [NO] to proceed to the LabCal Outputs? option.

FACTORY SETUP MENU
LabCal Outputs?

Press [YES] to calibrate the analog outputs.

Output to LabCal:
[A] B done

Use the [NO] or arrow keys to scroll to the desired output. Press [YES] to confirm
the entry.

Output A 20 mA Output
Enter mA [20.00]:

Use the numeric keys to enter actual output value (as read by a multimeter or control
device). Press [YES] to enter the number, and [YES] again to confirm the entry.

Output A 4 mA Output
Enter mA [4.00]:

Use the numeric keys to enter actual output value (as read by a multimeter or control
device). Press [YES] to enter the number, and [YES] again to confirm the entry.

Output to LabCal:
A [B] done

Use the [NO] or arrow keys to scroll to another output to repeat the calibration
procedure. Press [YES] to confirm the entry. If you have completed calibration,
scroll to “Done” and press [YES].

FACTORY SETUP MENU
LabCal Outputs?

Press [NO] to proceed to the Manual Offset? option.

«
...
64
65
66
67
68
...
»

Содержание TMO2D







































































































Отзывы:

Нет отзывов

Похожие инструкции для TMO2D

Бренд: Baby Control Digital Страницы: 12

SyncMaster C27A750X

Бренд: Samsung Страницы: 102

Бренд: L-Acoustics Страницы: 12

Бренд: Samsung Страницы: 92

Бренд: Samtron Страницы: 57

Бренд: XtendLan Страницы: 10

UMEN-260314-V1.0

Бренд: NewHawk Страницы: 14

FusionView FV 121

Бренд: Kontron Страницы: 69

4 Channel H.264 Compact DVR screen

Бренд: Sygonix Страницы: 78

Бренд: G-STORY Страницы: 41

Бренд: AOR Страницы: 39

Бренд: Greater Concepts Страницы: 84

HAP-19AV Series

Бренд: I-Tech Страницы: 28

Бренд: Mottura Страницы: 40

Бренд: InFocus Страницы: 58

PerfectView M5L

Бренд: Waeco Страницы: 156

Бренд: Neltronics Страницы: 19

Бренд: Eizo Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды