GE TMO2D Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 102

background image

TMO2D Digital Display User’s Manual

21

Chapter 4. Basic Programming

Chapter 4. Basic Programming

4.1 Introduction

The TMO2D display contains an interactive, user-friendly program that enables the user to change operating
parameters as desired.

This user program has six main menus. Use the front panel keypad and display to check or change the settings for
current operating parameters. The TMO2D stores data in memory and will retain it for several years if the main power
is lost. New data overrides any previously entered data.

The user program consists of six main menus:

•

Setup

•

Outputs

•

Relays

•

Tests

•

Calibration

•

System Log

Note:

The TMO2D can function as a display package for a variety of GE transmitters. As an example, this chapter
describes TMO2D programming when the TMO2D is used with a TMO2 or XMO2 oxygen transmitter.

4.2 Entering Data into the User Program

To enter data into the user program or to check previously entered values, enter the Menu Mode. When the power is
turned on, the TMO2D enters the Operate Mode. To enter the Menu Mode:

1.

Press the [NO] key.

2.

Key in the code [1] [2] [3]. The TMO2D will display an asterisk (*) after you enter each digit.

If an incorrect code is entered or a non-numeric ([YES]/[NO] or arrow) key is pressed rather than 1 2 3, the LCD will
automatically resume displaying data, and you must press [NO] to re-attempt the code. Once all three digits have been
entered correctly, the display will cease collecting data and the LCD will switch to Menu Mode.

The LCD screen now displays the Setup Menu, the first of the six main menus. At this display, press [YES] to enter this
menu, or [NO] to scroll to the next menu. Pressing [NO] repeatedly scrolls through all six main menus.

Note:

The first six options are main menus, while the

RESUME

prompt enables users to exit the Menu Mode and

return to Operate Mode.

«
...
27
28
29
30
31
...
»

Содержание TMO2D







































































































Отзывы:

Нет отзывов

Похожие инструкции для TMO2D

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 169

Бренд: Panasonic Страницы: 95

BrilliantVIEW SEW-3041W

Бренд: Samsung Страницы: 9

Бренд: A&D Страницы: 5

Digital VTH Series

Бренд: Dahua Страницы: 22

Бренд: Tatung Страницы: 27

Бренд: HANNspree Страницы: 23

Бренд: ADEMCO Страницы: 20

Babyviewer 2500

Бренд: Levita Страницы: 18

Бренд: CueScript Страницы: 5

Бренд: Barco Страницы: 78

Бренд: FEC Страницы: 22

MDSC-8358 MNA Series

Бренд: Barco Страницы: 54

ITRON Telecontrol TC-E

Бренд: Allmess Страницы: 4

Бренд: ViewSonic Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды