GE T60 Скачать руководство пользователя | Manualshive

Страница: 304 / 796

background image

5-158

T60 Transformer Protection System

GE Multilin

5.5 FLEXLOGIC

5 SETTINGS

5

The logic that determines the interaction of inputs, elements, schemes and outputs is field programmable through the use
of logic equations that are sequentially processed. The use of virtual inputs and outputs in addition to hardware is available
internally and on the communication ports for other relays to use (distributed FlexLogic).

FlexLogic allows users to customize the relay through a series of equations that consist of

operators

and

operands

. The

operands are the states of inputs, elements, schemes and outputs. The operators are logic gates, timers and latches (with
set and reset inputs). A system of sequential operations allows any combination of specified operands to be assigned as
inputs to specified operators to create an output. The final output of an equation is a numbered register called a

virtual out-

put

. Virtual outputs can be used as an input operand in any equation, including the equation that generates the output, as a

seal-in or other type of feedback.

A FlexLogic equation consists of parameters that are either operands or operators. Operands have a logic state of 1 or 0.
Operators provide a defined function, such as an AND gate or a Timer. Each equation defines the combinations of parame-
ters to be used to set a Virtual Output flag. Evaluation of an equation results in either a 1 (=ON, i.e. flag set) or 0 (=OFF, i.e.
flag not set). Each equation is evaluated at least 4 times every power system cycle.

Some types of operands are present in the relay in multiple instances; e.g. contact and remote inputs. These types of oper-
ands are grouped together (for presentation purposes only) on the faceplate display. The characteristics of the different
types of operands are listed in the table below.

Table 5–19: T60 FLEXLOGIC OPERAND TYPES

OPERAND TYPE

STATE

EXAMPLE FORMAT

CHARACTERISTICS

[INPUT IS ‘1’ (= ON) IF...]

Contact Input

On

Cont Ip On

Voltage is presently applied to the input (external contact

closed)

Off

Cont Ip Off

Voltage is presently not applied to the input (external

contact open)

Contact Output

(type Form-A contact

only)

Contact Closed

Cont Op 1 Closed

Contact output is closed

Current On

Cont Op 1 Ion

Current is flowing through the contact

Voltage On

Cont Op 1 VOn

Voltage exists across the contact

Voltage Off

Cont Op 1 VOff

Voltage does not exists across the contact

Direct Input

On

DIRECT INPUT 1 On

The direct input is presently in the ON state

Element

(Analog)

Pickup

PHASE TOC1 PKP

The tested parameter is presently above the pickup setting

of an element which responds to rising values or below the

pickup setting of an element which responds to falling

values

Dropout

PHASE TOC1 DPO

This operand is the logical inverse of the above PKP

operand

Operate

PHASE TOC1 OP

The tested parameter has been above/below the pickup

setting of the element for the programmed delay time, or

has been at logic 1 and is now at logic 0 but the reset timer

has not finished timing

Block

PHASE TOC1 BLK

The output of the comparator is set to the block function

Element

(Digital)

Pickup

Dig Element 1 PKP

The input operand is at logic 1

Dropout

Dig Element 1 DPO

This operand is the logical inverse of the above PKP

operand

Operate

Dig Element 1 OP

The input operand has been at logic 1 for the programmed

pickup delay time, or has been at logic 1 for this period and

is now at logic 0 but the reset timer has not finished timing

Element

(Digital Counter)

Higher than

Counter 1 HI

The number of pulses counted is above the set number

Equal to

Counter 1 EQL

The number of pulses counted is equal to the set number

Lower than

Counter 1 LO

The number of pulses counted is below the set number

Fixed

On

On

Logic 1

Off

Off

Logic 0

Remote Input

On

REMOTE INPUT 1 On

The remote input is presently in the ON state

Virtual Input

On

Virt Ip 1 On

The virtual input is presently in the ON state

Virtual Output

On

Virt Op 1 On

The virtual output is presently in the set state (i.e.

evaluation of the equation which produces this virtual

output results in a "1")

«
...
302
303
304
305
306
...
»

Содержание T60





























































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для T60

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 32

Бренд: Danfoss Страницы: 59

Бренд: Danfoss Страницы: 32

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 44

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 144

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 64

Бренд: Danfoss Страницы: 8

VLT AutomationDrive FC 360

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 6

Бренд: Danfoss Страницы: 4

Бренд: Danfoss Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды