GE Solar 8000M/i Скачать руководство пользователя страница 70

Страница: 70 / 192

4-18

Solar 8000M/i patient monitor

2026265-075C

Maintenance and checkout:

Checkout procedure

Procedures

Solar 8000M/i Unity View display

NOTE

This check only applies to Solar 8000M systems with product code

and

Refer to the specific manufacturer’s documentation.

Touchscreen

Verify that touching a parameter box displays the screen information for
that parameter.

Tram-rac housing

1. Verify that the power LED is ON at the Tram-rac housing.

2. Disconnect and reconnect the Tram-rac housing communication

cable. Verify the recovery of the waveforms.

3. If the Tram-rac housing has additional slots for input modules, insert

a BP module. Connect simulator and verify communication to the
monitor. Repeat for each slot.

4. If the Tram-rac housing has an optional power supply, check the

following on the connector that applies to your equipment.

16.5V is

not

present at pin 5 of the

TRAM-NET

connector with respect to pin 9.

16.5V is

not

present at pin 5 with respect to chassis

ground of the Tram-rac housing.

018A

Содержание Solar 8000M/i

































































































































































































Результаты поиска

Содержание Solar 8000M/i

Отзывы:

Похожие инструкции для Solar 8000M/i

Бренды по названию

Популярные бренды

GE Solar 8000M/i, Руководство по обслуживанию

Результаты поиска

Содержание Solar 8000M/i

Отзывы:

Похожие инструкции для Solar 8000M/i

Бренды по названию

Популярные бренды