GE Solar 8000M/i Скачать руководство пользователя страница 64

Страница: 64 / 192

4-12

Solar 8000M/i patient monitor

2026265-075C

Maintenance and checkout:

Electrical safety tests

Enclosure leakage current test

This test pertains to the Solar 8000M/i, part of the monitoring system.

Perform this test to measure current leakage through exposed conductive
surfaces on the device under test during normal operation.

1. Configure the leakage tester like the circuit shown below with GND

switch OPEN and polarity switch NORM.

2. Connect probe to an unpainted, non-anodized chassis ground on the

device under test.

3. Set the power switch of the device to ON.

4. Read the current leakage indicated on DMM.

NOTE

Center-tapped and non-center-tapped supply circuits produce
different leakage currents and the UL and EN limits are
different.

5. Set the polarity switch to RVS.

6. Read the current leakage indicated on DMM.

NOTE

If either reading is greater than the appropriate specification
below, the device under test fails. Contact GE Technical Support.

300

A (0.3 volts on the DMM), and the device under test is

powered from 100-120 V/50-60 Hz.

300

A (0.3 volts on the DMM), and the device under test is

powered from a centered-tapped 200-240 V/50-60 Hz, single
phase circuit.

500

A (0.5 volts on the DMM), and the device under test is

powered from a non-center-tapped, 200-240 V/50-60 Hz, single-
phase circuit.

7. Set the GND switch on the leakage tester to CLOSED.

8. Read the current leakage indicated on DMM.

Power Cord

Leakage Tester

NORM

RVS

HIGH

LOW

GND

0.015µF

Power Cord

Device

Under

Test

DMM set to measure AC voltage

GND

DMM

Closed

Open

Probe to exposed conductive chassis

10K

501A

Содержание Solar 8000M/i

































































































































































































Результаты поиска

Содержание Solar 8000M/i

Отзывы:

Похожие инструкции для Solar 8000M/i

Бренды по названию

Популярные бренды

GE Solar 8000M/i, Руководство по обслуживанию

Результаты поиска

Содержание Solar 8000M/i

Отзывы:

Похожие инструкции для Solar 8000M/i

Бренды по названию

Популярные бренды