GE Solar 8000M/i Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 192

background image

2026265-075C

Solar 8000M/i patient monitor

4-5

Maintenance and checkout:

Cleaning

Cleaning the Touch Screen Display

1. Turn OFF the mains power switch on the monitor and disconnect it

from the power source.

2. Clean the screen with an

ammonia free

glass cleaner and lint free

cloth.

CAUTION

Do not spray any glass cleaning solution or any general
cleaning solutions directly onto the monitor’s display
surface. Always dampen the towel and then clean the
screen.

Cleaning, disinfecting and storing GE ECG cables and leadwires

NOTE

These instructions supersede all cleaning/disinfecting instructions
for GE ECG Cables and Leadwires. All safety statements and notes
in the manual still apply.

Cleaning or disinfecting

1. Remove cables and leadwires from the handheld device or system

before cleaning.

2. Use care in cleaning leadwires to prevent pulling the long wires from

the connector ends. Metal connections can be pulled away from the
connectors.

3. For general cleaning of cables and leadwires, wipe using a lightly

moistened cloth with a mild soap and water solution. Then wipe and
air dry.

4. For disinfecting the cables and leadwires, wipe exterior with a soft

lint-free cloth, using the following solution as recommended in the
APIC Guidelines for Selection and Use of Disinfectants (1996):

Sodium hypochlorite (5.2% household bleach) minimum 1:500
dilution (minimum 100 ppm free chlorine) and maximum 1:10
dilution.

Any sodium hypochlorite wipe product that meets the above
guidelines of can be used.

NOTE

Wring excess disinfectant from wipe before using.

NOTE

Any contact of disinfectant solutions with metal parts may cause
corrosion.

5. Do

not

immerse either end of a cable or leadwire connector.

Immersing or “soaking” the connector ends may corrode metal
contact ends and affect signal quality.

6. Wipe off cleaning solutions with a clean, lightly moistened cloth.

«
...
55
56
57
58
59
...
»

Содержание Solar 8000M/i

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Solar 8000M/i

Бренд: Parker Страницы: 54

Бренд: NARGESA Страницы: 37

Бренд: NARGESA Страницы: 6

Бренд: Omlet Страницы: 60

Бренд: ValueStore US Страницы: 2

Бренд: Kärcher Страницы: 20

Бренд: Parker Research Corp Страницы: 3

Бренд: Wacker Neuson Страницы: 34

Aristo WeldCloud Mig U5000i

Бренд: ESAB Страницы: 28

Бренд: BRAND Страницы: 21

Бренд: Milestone Страницы: 40

Firefly 808 Universal

Бренд: Phonic Страницы: 27

WaterLink Spin Touch DW

Бренд: LaMotte Страницы: 64

High End Systems SolaPix 7

Бренд: ETC Страницы: 36

DL30x30-G525/24V

Бренд: Vision & Control Страницы: 32

Бренд: Ultra Products Страницы: 1

Бренд: Waldman Страницы: 60

Бренд: Struers Страницы: 95

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды