background image

– 24 

Process Tube

Signal Wire Connector from Main Board

Line-In

Compressor Lead Wires

WARNING:

  When the refrigerator is plugged in, 

120 VAC is always present at the inverter. 

Note:

 Certain voltmeters will not be able to read 

voltage output from the inverter. If no voltage 
or erratic voltage is measured, it does not 
necessarily indicate a faulty inverter.

The inverter receives 120 VAC line-in from the 
power supply. The inverter converts this single-
phase, 60 Hz, 120 VAC into 3-phase,  230 VAC, 
with frequency variations between 57 Hz and 104 
Hz. This voltage is delivered to the compressor 
through 3 lead wires. Each wire will carry identical 
voltage and frequency.  

Note:

 The compressor leads must be connected 

to measure voltage output. If the compressor 
wires are not connected, or if an open occurs in 
one of the 3 lead wires or in the compressor, the 
inverter will stop voltage output.

Inverter Shown with Cover Removed

N

L1

Caution:

 It may be necessary to bend the 

process tube in order to remove the inverter. If 
it is necessary to bend the process tube, use 
extreme caution.

2.  Rotate the inverter counterclockwise and 

slide it forward to release the tabs from the 
mounting bracket.

Back Tab

Right Side Tab

Back Tab

Mounting Bracket

Back View

Left Side View

Inverter Front

Inverter

The inverter is accessed from the back of the 
refrigerator. 

It is located on the left side of the compressor 
behind the water valve. 

• 

The water valve must be removed to access 
the inverter.

To remove the Inverter

1. Remove 

the 

1

/

4

-in. hex-head screw that holds 

the inverter in place.

Inverter

Inverter Viewed From the Front

Содержание PSH23PGR Series































































Отзывы: