manualshive.com logo in svg

GE PanaFlow HT, Руководство пользователя

Поделиться
Скачать
GE PanaFlow HT Скачать руководство пользователя страница 33

PanaFlow HT User’s Manual

23

Chapter 2. Installation

2.6.1 Remote Mount Wiring Instructions

WARNING! Be sure to remove power before performing these steps!

In the lower chamber of the enclosure is the Transducer Junction box. In the case of remote mount, a duplicate box is 
mounted on the pipe stand. Follow these instructions to connect the two junction boxes using the remote mount cable 
supplied.

1.

Loosen the set screw on the junction box cover and remove the cover.

2.

Inside the wiring area of these two enclosures is a round printed circuit board with two mounting screws. Loosen 
the mounting screws, insert your fingers in the two 1-cm round holes, and twist the board counter-clockwise (in the 
direction of the arrows) approximately 2 cm to release it from the enclosure. The board will remain wired to the 
system, but with enough slack to pull the board out about 5 cm. The transducer connections are on the other side of 
the board.

 

Figure 18: Removing the Board

3.

Make the mechanical connection between the remote cable and the junction boxes. Install the cable into the wiring 
port on each enclosure end and tighten the cable glands per manufacturer instructions.

4.

At the Flowcell end, connect MCX cables from the remote mount cable to MCX connectors MCX-J1 (Ch1 Up) and 
MCX-J11 (Ch1 Dn). For a 2-channel system, also connect to MCX-J3 (Ch2 Up) and MCX-J9 (Ch2 Dn). 

5.

At the Electronics end, connect BNC cables from the remote mount cable to BNC connectors BNC-J1 (Ch1 Up) 
and BNC-J6 (Ch1 Dn). For a 2-channel system also connect to BNC-J2 (Ch2 Up) and BNC-J5 (Ch2 Dn).

Содержание PanaFlow HT




































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды