GE PACSystems* RX3i Скачать руководство пользователя страница 77

Страница: 77 / 116

show profinet

GFK-2572

Chapter 2 Monitor Level Commands

2-61

Field Definitions

The following table defines the fields shown in the preceding examples:

Field

Description

PNCDevice Name

The PROFINET Device Name of the PROFINET Controller.

Provider State

The PROFINET Provider state that is sent with each RTC frame.

This reflects the state of the PLC CPU’s Output Enable line. The

possible states and meaning are:
Run –the PLC CPU’s Output Enable is enabled.
Stop –the PLC CPU’s Output Enable Line is disabled.

Dev#

The Device number associated with the Remote I/O Device.

AR#

A number the PROFINET Controller associates with the

Application Relationship’

s ARUUID that uniquely identifies a

particular AR. The possible values are 001 through 999.

ARStat

Indicates the Application Relationship (AR) connection and

control status. The possible values are:
Disconn – the AR has not successfully been established with the

specified remote IO device.
LocCtrl – the AR is established and the local PNC has the

Primary AR.
RemCtrl – the AR is established and a different PNC has the

Primary AR.
NoCtrl – the AR is established but no PNC has the Primary AR.

DeviceName

Specifies the PROFINET Device Name of the associated Remote

IO Device.

Vendor

Remote Device PROFINET Vendor ID used to specify an IO-

Device’s vendor on the PR

OFINET network.

Device

Remote Device PROFINET Device ID used to specify an IO-

Device’s type on the PROFINET network.

Vendor Description

An optional description provided by the Remote IO-Device that is

vendor specific (typically contains model name and/or catalog

number). If the IO-Device does not provide this information, the

field is blank.

ARUUID

A number that uniquely identifies a particular AR within the

system.

Redundancy Type

Indicates whether this AR is part of a PNIO System Redundancy

set or not. The possible values are Simplex AR and System

Redundancy AR.

ARType

Indicates the type of AR. The possible values are IOCARSingle

and IOCARSR. The IOCARSR indicates System Redundancy or

Configure in Run.

ARProperties

Displays the binary value of the AR Properties field for the

Application Relationship. The actual properties are decoded in

the indented fields just below the ARProperties field

(PullModuleAlarmAllowed, CompanionAR, etc.).

Содержание PACSystems* RX3i





















































































































Результаты поиска

Содержание PACSystems* RX3i

Отзывы:

Похожие инструкции для PACSystems* RX3i

Бренды по названию

Популярные бренды

GE PACSystems* RX3i, Руководство по интерфейсу командной строки

Результаты поиска

Содержание PACSystems* RX3i

Отзывы:

Похожие инструкции для PACSystems* RX3i

Бренды по названию

Популярные бренды