manualshive.com logo in svg

GE MM200, Быстрый старт, Страница: 43 / 45

Поделиться
Скачать
GE MM200 Скачать руководство пользователя страница 43

38

MM200 MOTOR MANAGEMENT SYSTEM – QUICK START GUIDE

BACKUP AND RESTORE SETTINGS

CHAPTER 8: MAINTENANCE

Unscheduled maintenance (system interruption)

•

View the last trip data for correct operation of inputs, outputs, and elements.

Backup and restore settings

Back up a copy of the in-service settings for each commissioned MM200 device, so as to 
revert to the commissioned settings after inadvertent, unauthorized, or temporary setting 
changes are made, after the settings defaulted due to firmware upgrade, or when the 
device has to be replaced. This section describes how to backup settings to a file and how 
to use that file to restore the settings to the original relay or to a replacement relay.

Backing up settings

Setpoints must be saved to a file on the local PC before performing any firmware 
upgrades. Saving Setpoints is also highly recommended before making any Setpoint 
changes or creating new Setpoint files.
The Setpoint files in the EnerVista MM300/MM200 Setup window are accessed in the Files 
Window. Use the following procedure to download and save Setpoint files to a local PC.
1.

Ensure that the site and corresponding device(s) have been properly defined and 
configured as shown in 

Connecting EnerVista MM300/MM200 Setup to the Relay

, 

above.

2.

Select the desired device from the site list.

3.

Select the 

Online > Read Device Settings 

from Device menu item (at the top of the 

page), or right-click on the device and select 

Read Device Settings

 to obtain settings 

information from the device.

4.

After a few seconds of data retrieval, the software will request the name and 
destination path of the setpoint file. The corresponding file extension will be 
automatically assigned. Press 

Receive

 to complete the process. A new entry will be 

added to the tree, in the File pane, showing path and file name for the setpoint file.

Restoring settings

CAUTION: 

An error message will occur when attempting to download a setpoint file with a 
revision number that does not match the relay firmware. If the firmware has been 
upgraded since saving the setpoint file, see 

Upgrading Setpoint Files to a New Revision, 

above, for instructions on changing the revision number of a setpoint file.

The following procedure illustrates how to load setpoints from a file. Before loading a 
setpoints file, it must first be added to the EnerVista MM300/MM200 Setup environment as 
described in the section, 

Adding Setpoints Files to the Environment

.

1.

Select the previously saved setpoints file from the File pane of the software main 
window.

2.

Select the 

Offline > Edit Settings File Properties

 menu item and verify that the 

corresponding file is fully compatible with the hardware and firmware version of the 
target relay. If the versions are not identical, see 

Upgrading Setpoint Files to a New 

Revision

, above, for details on changing the setpoints file version.

3.

Right-click on the selected file and select the 

Write Settings File to Device

 item.

4.

Select the target relay from the list of devices shown and click 

Send

. If there is an 

incompatibility, an "Incompatible Device" error message will occur:

Содержание MM200














































Отзывы:

Нет отзывов