GE Mini Telemetry Скачать руководство пользователя страница 17

Страница: 17 / 71

2049809-001 Rev B

Chapter 2:

Safety

The information presented in this section is important for the safety of both the patient and operator and also

serves to enhance equipment reliability. This chapter describes how the terms Danger, Warning, Caution,

Important and Note are used throughout the manual. In addition, standard equipment symbols are defined.

General Information

General Use

If any equipment is cold to the touch or below ambient temperature, allow it to stabilize to ambient temperature

before use.

To ensure patient safety, use only parts and accessories manufactured or recommended by GE Medical Systems

Information Technologies. Parts and accessories used shall meet the requirements of IEC 60601-1.

Disposable devices are intended for single use only. They should not be reused.

Periodically and whenever the integrity of the equipment is in doubt, test all functions as indicated under the

section

“Chapter 4: Installation and Setup” on page 19

Refer to the “Maternal/Fetal Monitoring Operator’s Manual” for information concerning the limitations of internal

and external fetal heart rate monitoring techniques.

Responsibility of the Manufacturer

GE Medical Systems Information Technologies (hereafter Information Technologies) is responsible for the effects

on safety, reliability and performance if:
• Assembly operations, extensions, readjustments, modifications, or repairs are carried out by persons

authorized by Information Technologies.

•

The electrical installation of the relevant room complies with appropriate regulations.

•

The equipment is used in accordance with the instructions for use.

Содержание Mini Telemetry



































































Результаты поиска

Содержание Mini Telemetry

Отзывы:

Похожие инструкции для Mini Telemetry

Бренды по названию

Популярные бренды

GE Mini Telemetry, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Mini Telemetry

Отзывы:

Похожие инструкции для Mini Telemetry

Бренды по названию

Популярные бренды