manualshive.com logo in svg

GE LOGIQ S8, Руководство по обслуживанию

GE LOGIQ S8 - это передовой ультразвуковой аппарат, предназначенный для точной диагностики. Вы можете загрузить бесплатно Руководство по обслуживанию для этого устройства на manualshive.com, чтобы ознакомиться с функциями и правильным использованием. Не упустите возможность ознакомиться с этим руководством!

Поделиться
Скачать
background image

GE H

EALTHCARE

PROPRIETARY TO GE

D

IRECTION

 5394227, 12

 

LOGIQ S8/LOGIQ E8 S

ERVICE

M

ANUAL

 

Section 3-7 - Power On/Off

3 - 17

Section 3-7

Power On/Off 

 

NOTE:

If the battery option is installed (R4 or later)

The extended battery/small battery is charged automatically when the LOGIQ S8 is connected to the 
wall outlet via the power cable and circuit breaker is turned on whether the LOGIQ S8 is turned on or in 
standby-mode.

But you can turn off the circuit breaker and disconnect the power cable when the battery is charging.

•

While the extended battery/small battery charging, a fan is running. a fan stops automatically when 

battery is fully charged.

•

While the extended battery charging, the LED is blinking and turn off when the battery is fully 

charged.

DANGER

ALWAYS CONNECT THE UNIT TO A FIXED POWER SOCKET WHICH HAS THE 
PROTECTIVE GROUNDING CONNECTOR.

DANGER

NEVER USE A THREE-TO-TWO PRONG ADAPTER; THIS DEFEATS THE 
SAFETY GROUND.

DANGER

ENSURE THAT THE POWER CORD AND PLUG ARE INTACT AND THAT THE 
POWER PLUG IS THE PROPER HOSPITAL-GRADE TYPE (WHERE REQUIRED).

CAUTION

LOGIQ S8 REQUIRES ALL COVERS.
OPERATE THIS UNIT ONLY WHEN ALL BOARD COVERS AND FLAME PANELS ARE SECURELY 
IN PLACE. THE COVERS ARE REQUIRED FOR SAFE OPERATION, GOOD SYSTEM 
PERFORMANCE AND COOLING PURPOSES.

NOTICE

User only power supply cords, cables and plugs provided by or designated by GE Healthcare.

NOTICE

After turning off the system, wait at least 10 seconds before turning it on again. The system may not 
be able to boot if power is recycled too quickly.

Содержание LOGIQ S8



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LOGIQ S8

UnionSpecial 2200 Series Instructions, Engineer'S And Illustrated Parts Manual preview
2200 Series
Бренд: UnionSpecial Страницы: 56
Fein GBA 18V Manual preview
GBA 18V
Бренд: Fein Страницы: 248
ZF 400 Series Operating Instructions Manual preview
400 Series
Бренд: ZF Страницы: 30
Raymarine ST7000 Owner'S Handbook Manual preview
ST7000
Бренд: Raymarine Страницы: 111
Latchways R20 User Instructions preview
R20
Бренд: Latchways Страницы: 80
Kapriol 27956 Manufacturer'S Instruction And Information preview
27956
Бренд: Kapriol Страницы: 28
YATEK ECO Owner'S Manual preview
ECO
Бренд: YATEK Страницы: 72
GARANT SG1 Operation Manual preview
SG1
Бренд: GARANT Страницы: 239
p-light Midi Installation And Instructions For Use preview
Midi
Бренд: p-light Страницы: 36
Hantek DPO6000 Series Product Manual preview
DPO6000 Series
Бренд: Hantek Страницы: 124
Hameg HO720 Installation Manuallines preview
HO720
Бренд: Hameg Страницы: 10
Tascam SX-1 Brochure & Specs preview
SX-1
Бренд: Tascam Страницы: 8
Nabtesco Symphony NK-6 User Manual preview
Symphony NK-6
Бренд: Nabtesco Страницы: 26
Naked NKD1 Installation & Operating Manual preview
NKD1
Бренд: Naked Страницы: 36
Meyer Boss 8200 RT Owner/Operator’S Manual & Parts Book preview
Boss 8200 RT
Бренд: Meyer Страницы: 100
Orlit Rovelight RT-400 Manual preview
Rovelight RT-400
Бренд: Orlit Страницы: 16
Emos ZYP0201 Quick Start Manual preview
ZYP0201
Бренд: Emos Страницы: 8
Drive Medical Celestia 18250 Instruction Manual preview
Celestia 18250
Бренд: Drive Medical Страницы: 26

Бренды по названию

Популярные бренды

Загрузить еще бренды