manualshive.com logo in svg

GE LOGIQ S8, Руководство по обслуживанию

Поделиться
Скачать
GE LOGIQ S8 Скачать руководство пользователя страница 363

GE H

EALTHCARE

D

IRECTION

 5394227, 12

 

LOGIQ S8/LOGIQ E8 S

ERVICE

M

ANUAL

 

Section 7-8 - Error messages

7 - 93

7-8-1

FibroScan Module Error messages and Logs

Table 7-21:

 Error messages and Logs

Message: A system reboot is required to connect to the FibroScan 
module.

The system has detected FibroScan Module connection is not available. 
Reboot the system.
Cause: The network connection between FibroScan Module and the 
system was disconnected during FibroScan mode, and connection 
recovery failed.

Message: FibroScan is not available. A FibroScan module is required

The system could not detect FibroScan Module. Please check below 
steps:
1. FibroScan Module is mounted on the system
2. Green LED on FibroScan Module is ON

3. Blue LED on FibroScan Module is ON

If either of above step is failed, go to trouble shooting.
Cause: The system did not detect an established network connection 
between FibroScan Module and the system on boot up.

Message: Shutting down FibroScan Module, please wait...
The system will be shutting down in a moment. The system will shut down 
FibroScan Module safely before shutting down itself. The system will 
proceed on shut down after message disappears.

Message: FibroScan connection is not available. Reconnecting... this 
could take up to 30 seconds.

The system has detected FibroScan Module connection is not available. 
The system is trying to reconnect to FibroScan Module. Please simply 
wait for the reconnection process to end. The message will disappear if 
reconnection is successful. You could continue the FibroScan 
measurement if reconnection is successful. 
Cause: A network disconnection has occurred during FibroScan mode. 

Message: FibroScan reconnection failed. System will exit FibroScan 
mode. FibroScan data may not be saved.

The system has detected FibroScan Module connection is not available, 
and reconnection process has failed. The system will force exit 
FibroScan mode without storing FibroScan measurement data.
Cause: A network disconnection has occurred during FibroScan mode.

Содержание LOGIQ S8



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды