manualshive.com logo in svg

GE IMP2B, Справочник по аппаратуре

Поделиться
Скачать
GE IMP2B Скачать руководство пользователя страница 25

Publication No. IMP2B-0HH/5 

Functional Description  25 

3.9  Ethernet 

The MV64560 provides two Ethernet MACs that are capable of 10/100/1000BaseT 
Ethernet. These are connected to the physical interface by two Marvell 88E1111 
PHYs. The network (MAC) addresses are factory configured and cannot be altered in 
the field. 

Both channels are available through the 

J2 connector

, either as two 10/100BaseT ports 

or one 10/100/1000BaseT port, software selectable. 

Twelve associated status 

LEDs

 are mounted on the rear of the board. The default 

functions of these LEDs are Tx activity, Rx activity, Duplex, Link 10, Link 100 and 
Link 1000, but these functions may be overridden by software. 

3.10  USB 2.0 

The MV64560 provides two USB 2.0 OCHI/EHCI-compliant Host Ports, which are 
routed to the 

J2 connector

. Each port has a software-enabled power controller 

capable of providing up to 0.5 Amps of power at +5.0 V. For more details, see the 
EPLD 

Control Register 1

. 

3.11  Timers 

The MV64560 provides four 32-bit timer/counters that operate at a frequency of 
133 MHz and have a resolution of 7.5 ns. 

There is an option for software to cascade two timers to form a 64-bit timer/counter. 
This is done by connecting the terminal count signal of Timer 2 (TC_NTn[2]) to the 
count enable input of Timer 3 (TC_ENn[3]) using the Multi-Purpose Pins and the 
EPLD 

Control Register 1

. 

3.12  Watchdog Timer 

The MV64560 provides a 32-bit watchdog timer. The count-down timer is loaded 
with a preset value and must be serviced periodically to prevent it expiring. The 
watchdog timer operates at a frequency of 133 MHz and has a resolution of 7.5 ns. It 
is disabled by default following reset. 

Two thresholds may be set. The first generates an interrupt to the processor and the 
second causes a hard reset to the local processor. 

Содержание IMP2B
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды