GE IMP2B страница 38 Скачать руководство пользователя

Страница: 38 / 55

38 IMP2B 3U cPCI Single Board Computer

Publication No. IMP2B-0HH/5

3.19 Interrupts

The IMP2B uses the interrupt controller provided in the MV64560. The interrupt
sources are fed into the multi-purpose pins and routed internally to the CPU
interrupt output.

Table 3-25 Interrupt Mapping

Interrupt Source MV64560 MPP Pin Notes
cPCI INTA

MPP(8)

cPCI INTB

MPP(9)

cPCI INTC

MPP(10)

cPCI INTD

MPP(11)

PMC INT(A:B:C:D)

MPP(16)

PMC_INTA# (J11-4), PMC_INTB# (J11-5), PMC_INTC#, (J11-6) and
PMC_INTD# (J11-9) are wired together

EPLD INT#

MPP(19)

Derives from the EPLD from the interrupts sources below

GPIO INT#

MPP(21)

Derives from the GPIO block within the EPLD

The EPLD combines the following interrupts to produce EPLD INT#:

Table 3-26 Interrupt Combination

Interrupt

Source

Cause

RTC_INT#

Real Time Clock

TEMP_INT#

Ambient sensor or CPU junction temperature sensor Temperature

TEMP_CRT#

Ambient sensor or CPU junction temperature sensor Critical temperature

PHY0_INT#

Ethernet PHY0

PHY2_INT#

Ethernet PHY2

OVR_AA#

USB 2.0 Port 0 power controller

Overload

OVR_AB#

USB 2.0 Port 1 power controller

Overload

The

EPLD Interrupt Register

allows each of the above interrupts to be individually

masked, and also shows the interrupts that are active.

Содержание IMP2B
























































Результаты поиска

Содержание IMP2B

Отзывы:

Похожие инструкции для IMP2B

Бренды по названию

Популярные бренды

GE IMP2B, Справочник по аппаратуре

Результаты поиска

Содержание IMP2B

Отзывы:

Похожие инструкции для IMP2B

Бренды по названию

Популярные бренды