manualshive.com logo in svg

GE IC690ACC001, Руководство пользователя

Поделиться
Скачать
GE IC690ACC001 Скачать руководство пользователя страница 43

Product Certifications and Installation Guidelines for Conformance

 

 38 

PACSystems* RXi Box IPC 

GFK-2785C

 

Government Regulations 

The FCC requires the following note to be published according to FCC guidelines: 

Note:

  This equipment has been tested and found to comply with the limits for a Class A digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference when the equipment is operated in a commercial 
environment. This equipment generates, uses, and can radiate radio frequency energy and, if 
not installed and used in accordance with the instruction manual, may cause harmful 
interference to radio communications. Operation of this equipment in a residential area is 
likely to cause harmful interference in which case the user will be required to correct the 
interference at his or her own expense.

 

Note:

  Changes or modifications to this unit that are not expressly approved by GE Intelligent 

Platforms could void the user’s authority to operate the equipment. 

Industry Canada requires the following note to be published: 

Note:

 

This Class A digital apparatus complies with CAN ICES-3 (A)/NMB-3(A). 

Содержание IC690ACC001













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды