GE iBox Скачать руководство пользователя

Страница: 5 / 172

GE Grid Solutions

iBox/iBox Kit

Installation and Maintenance Guide

GE Information

994-0047-5.10-4

About This Document

Purpose

What this

document

provides

The

iBox/iBox Kit

Installation and Maintenance Guide

contains information about

two products, the iBox and the iBox Kit.
The document is split into three sections.

Section 1: Getting Started

provides an

overview of the iBox.

Section 2: iBox Installation and Maintenance

provides

instructions for installing, configuring, using, maintaining and troubleshooting the

iBox.

Section 3: iBox Kit Installation and Maintenance

provides similar information

for the iBox Kit.
Some iBox configuration procedures provide details on the SGConfig tool. For the

equivalent information when using SGConfig to configure the iBox, refer to the

SGConfig online help.

SGConfig

Online Help

For topics related to the use of GE Digital Energy's SGConfig* configuration utility,

or details of any software application used in a specific iBox, refer to the SGConfig

online help.

Training Tool

In addition to the primary purpose of this Installation and Maintenance Guide, its

secondary purpose is that of a Training Manual for customer training sessions

provided by GE Digital Energy, or its agents.

Operating

System

The procedures in this guide are based on Windows 2000. Some steps and dialog

boxes may vary slightly if you are using Windows XP or Windows 2003.

Intended Audience

Job Titles

This guide is intended for use by the SCADA system installers and field engineers

who are responsible for the installation, hardware configuration and maintenance of

SCADA systems containing iBox units and iBox Kits.

Experience &

Abilities

This guide assumes that anyone working with an iBox or iBox Kit has some prior

knowledge of:

•

Electrical utility industry

•

Personal computer terminology and interconnection skills

•

GE Digital Energy products

•

Other industry products such as protective relays, meters, and voltage regulators.

Содержание iBox













































































































































































Результаты поиска

Содержание iBox

Отзывы:

Похожие инструкции для iBox

Бренды по названию

Популярные бренды

GE iBox, Руководство по установке и обслуживанию

Результаты поиска

Содержание iBox

Отзывы:

Похожие инструкции для iBox

Бренды по названию

Популярные бренды