GE Hydran M2-X страница 121 Скачать руководство пользователя

Страница: 121 / 204

Page 121

Hydran* M2-X Instruction Manual

MA-029

Rev. 1.0,

30-Jul-18

7.1.2

Alarm Monitoring

The

alarm monitoring

method solves the disadvantages of the

periodic, visual

monitoring

method as follows:

•

Connecting the alarm contacts to an alarm panel (or any other SCADA

system) located in the station’s control room.

•

Continuous alarm monitoring.

•

Visual, periodic (weekly) reading of the gas and moisture levels on the display
of the Hydran M2-X

’s (for details, see Section

7.2).

•

Manual logging of gas level readings.

For details on the alarms and relays operation, see Chapter 6.

7.1.2.1

Method Drawbacks

The

alarm monitoring

method solves the response time inadequacy of the

periodic, visual

monitoring

method, but does not provide any information to

anticipate and prevent alarms.

Moreover, there is no information immediately available for an evaluation of the

severity of this alarm. A site inspection is required to perform the alarm evaluation.

7.1.3

Analog Outputs Monitoring

The

analog outputs monitoring

(gas and moisture level monitoring via the analog

output) solves the disadvantages of the

alarm monitoring

method as follows:

•

Connecting the Hydran M2-X

’s optional analog outputs to a SCADA system.

The Hydran M2-X has analog outputs that allow you to monitor the gas and
moisture level evolution.

•

Using a SCADA system to generate alarms based on the collected data.

•

Visual, periodic (weekly) reading of the gas and moisture levels on the display
of the Hydran M2-X

’s (for details, see Section

7.2).

It is recommended to use a SCADA system that offers the following advantages:

•

Gas and moisture level readings from the control room.

•

Regular processing data analysis.

•

Detection of any alarm when the specified alarm conditions are present. The

system’s response time must be short enough for the application’s needs.

•

Safe storage of the history files data in a format that allows easy analysis
from a host computer.

Содержание Hydran M2-X













































































































































































































Результаты поиска

Содержание Hydran M2-X

Отзывы:

Похожие инструкции для Hydran M2-X

Бренды по названию

Популярные бренды

GE Hydran M2-X, Инструкция по эксплуатации

Результаты поиска

Содержание Hydran M2-X

Отзывы:

Похожие инструкции для Hydran M2-X

Бренды по названию

Популярные бренды