background image

 
 

 
 

GE 
Lighting 

Evolve™ LED Area Light

 

Scalable Fixtures (EAS)  
 

Troubleshooting 

and Repair Guide 

 

 
This device complies with Part 15 of the FCC Rules. 
Operation is subject to the following two conditions: (1) This 
device may not cause harmful interference, and (2) this 
device must accept any interference received, including 
interference that may cause undesired operation. This 
Class [A] RFLD complies with the Canadian standard ICES-
003. Ce DEFR de la classe [ A ] est conforme à la NMB-003 
du Canada. 
 
Note: This equipment has been tested and found to comply 
with the limits for a Class A digital device, pursuant to part 
15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference when 
the equipment is operated in a commercial environment. 
This equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause 
harmful interference to radio communications. Operation 
of this equipment in a residential area is likely to cause 
harmful interference in which case the user will be required 
to correct the interference at his own expense 

• 

  This luminaire is designed for outdoor lighting service, and 

should not be used in areas of limited ventilation, or in high 
ambient temperatures.  
 

• 

  Best results will be obtained if installed and maintained 

according to the 

product’s installation instructions.   Refer to 

installation instructions if reinstalling after repair. 
 

• 

  Refer to product installation instructions and product 

datasheet for specifications and installation details. 

 

BEFORE YOU BEGIN 

Read these instructions completely  
and carefully. Save these instructions  
for future use. 

STOP

 

WARNING

 

!

 

Risk of electrical shock

. Disconnect power before servicing  

or installing product. 

WARNING

 

!

 

 

 

Risk of injury or damage. 

Unit will fall if not installed properly. 

Follow installation instructions. 

CAUTION

 

!

 

Risk of injury. 

Wear safety glasses and gloves during 

installation and servicing. 

Содержание Evolve












Отзывы: