manualshive.com logo in svg

GE Ettan IPGphor 3, Руководство по эксплуатации

Поделиться
Скачать
GE Ettan IPGphor 3 Скачать руководство пользователя страница 79

Edit step or gradient

Press the EDIT key to display the programmable parameters on the display.
Position the cursor in the field to be edited using the Right and Left arrow
keys and adjust the value by pressing the Up and Down arrow keys.

1

Access a Step by placing the cursor under the step number and use the
Right and Left arrow keys.

2

Each step is identified by “S” and the step number. The original programmed
option is Step for each step.

P r o t #   1   3   S t e p s
S 1   S t e p   5 0 0 V   1 : 0 0   H r s
S 2   S t e p   1 0 0 0 V   4 : 0 0   H r s
S 3   S t e p   8 0 0 0 V   8 0 0 0 0   V h r

To advance to the next step group press the Down arrow key and to return
to a previous step group press the Up arrow key.

3

To toggle to Gradient, move the cursor to the Step field using the Right and
Left arrow keys and toggle with the Up or Down arrow key.

4

P r o t #   1   3   S t e p s
S 1   G r a d   5 0 0 V   1 : 0 0   H r s
S 2   G r a d   1 0 0 0 V   4 : 0 0   H r s
S 3   S t e p   8 0 0 0 V   8 0 0 0 0   V h r

IEF voltage is programmable from 0–8000 V in increments of 10 V. Each of
the first three digits in the voltage field can be set independently.

5

First move the cursor to the desired digit location using the Right and Left
arrow keys and then change the value using the Up and Down arrow keys.

P r o t #   1   3   S t e p s
S 1   G r a d   5 0 0 V   1 : 0 0   H r s
S 2   G r a d   2 0 0 0 V   1 : 0 0   H r s
S 3   S t e p   8 0 0 0 V   2 : 0 0   H r s

Ettan IPGphor 3 Operating Instructions 28-9635-51 AC

79

5 Operation

5.3 Perform a run from the control panel

5.3.3 Set protocol parameters

Содержание Ettan IPGphor 3

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды