GE Digital Energy LP 33 Series страница 13 Скачать руководство пользователя

Страница: 13 / 38

Digital Energy™

OPM_LPS_3UI_10K_20K_0US_V010.doc

13/38

Installation Guide

LP 33

/ 10 - 20 kVA

3.2 DELIVERY

When delivered, check carefully the

package integrity

and the

physical conditions of the UPS

equipment

In case of any damage sustained during transport, immediately inform the carrier and contact your
local

Service Center

detailed report

of the damage is necessary for any insurance claim.

NOTE !

A damaged UPS must never be installed or connected to

utility

battery

3.3 STORAGE

The equipment is carefully packed for
transport and storage so that it is in a perfect
condition when eventually installed.

Never leave an UPS outside the building and
do not store the UPS one on top of the other.

It is recommended to store the UPS in its
original package in a

dry, dust free room

and far away from chemical substances,
with temperature not exceeding -13°F

131°F

(-25°C to 55°C).

3.3.1

Storage of the UPS

Some important functions of the UPS, such as the customized functions, are defined by
parameters stored in a

RAM memory

The RAM is supplied by a small

backup battery

located on the

Control Unit board

If the storage time of the UPS exceeds

1 year

these functions

should be verified

by an

authorized

Service Center

before putting the UPS into operation.

NOTE !

In case of storage of the UPS pay attention to:

FRAGILE

SENSITIVE

TO DAMPNESS

TO HEAT

SENSITIVE

TO FROST

SENSITIVE

Содержание Digital Energy LP 33 Series







































Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды

GE Digital Energy LP 33 Series, Руководство по установке

Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды