GE DHDVH52 Скачать руководство пользователя страница 44

Страница: 44 / 50

Remove the 3 Phillips-head screws that attach
the control board assembly to the control board
housing. Remove the control board.

Control Board Assembly

The control board assembly is mounted in a plastic
housing that is attached to the inside of the control
panel. It consists of 2 circuit boards connected by
a ribbon. The boards and the plastic housing are
replaced as an assembly.

Operation of the control board assembly can be
checked by using the service test mode. (See

Service

Test Mode

Error codes that are speciﬁ c to the control board
can initiate error codes E01, E61, E80, and E81. (See

Service Test Mode

To remove the control board assembly:

Caution:

To avoid marring the control panel, place

the panel face down on a protective surface.

Remove the top panel and the control panel.
(See

Top Panel and Control Panel

Remove the control knob by pulling outward.

Remove the plastic wire tie that attaches
the control board ribbon to the control panel
mounting bracket.

Remove the gasket seals from the right and left
ends of the control panel mounting bracket.

Remove the 4 Phillips-head screws that attach
the control panel mounting bracket to the
control panel. Remove the bracket.

Note:

Each cycle selection button assembly is held

to the plastic housing with a locking tab(s) and
strut(s) system.

Press the locking tab(s) then carefully lift each
cycle selection button to clear the strut(s) from
the plastic housing.

Note:

The replacement control board will always enter
into test mode t01 on initial power-up.

If replacing the control board, the dryer will not
function until the replacement control board has
been programmed.

To program the replacement control board:

Reconnect power to the dryer. (The display will
now show "---", which means no model has
been selected.)

Rotate the cycle knob until the correct model
number is displayed:

Select 1 for model DHDVH52EF/GF

Select 2 for model DBVH512EF/GF

Select 3 for model DCVH515EF/GF

Press and hold the Start/Pause key for 3
seconds. (The control will beep, indicating the
new model number has been successfully
programmed.)

Press the Power button to return to the test
selection mode.

Note:

If an error is made in programming the

control, enter test mode and select T01. Then repeat
steps 1 thru 3.

•

Strut

Locking Tab

Concealed Screw Locations

Gasket Seals

Содержание DHDVH52



















































Результаты поиска

Содержание DHDVH52

Отзывы:

Похожие инструкции для DHDVH52

Бренды по названию

Популярные бренды

GE DHDVH52, Техническое обслуживание руководство

Результаты поиска

Содержание DHDVH52

Отзывы:

Похожие инструкции для DHDVH52

Бренды по названию

Популярные бренды