GE Corometrics 250cx Series Скачать руководство пользователя

Страница: 215 / 252

Revision C

250cx Series Maternal/Fetal Monitor

6-23

2036947-001

Parts List, Drawings, and Replacement: Assembly/Disassembly of FRUs

24. Connect 20-conductor DSP-to-LCD Decoder ribbon cable to DSP board

connector J2.

25. Connect 8-conductor Inverter cable to DSP board connector J1.

26. Place DSP board onto Main board. Use two screws to fasten DSP board to

chassis.

27. Replace top cover. Re-insert screws.

2025177-021 Display Assembly

1. Remove top cover. Keep screws aside.

Remove two screws fastening DSP board to chassis.

Remove DSP board from Main board.

Disconnect 8-conductor Inverter cable from DSP board connector J1.

Disconnect 20-conductor DSP-to-LCD Decoder ribbon cable from DSP board
connector J2.

Disconnect 10-conductor DSP-to-Keypad ribbon cable from DSP board
connector J5.

Disconnect external display cable from J9 on DSP/Display PWA.

Open Recorder door, as it will interfere with front bezel movement.

Tilt the front bezel forward, away from the chassis.

10. Disconnect 10-conductor Keypad-to-Volume ribbon cable from Volume board

connector.

11. Remove screw fastening Display mounting bracket to front bezel.

12. Remove screw fastening bracket to Display assembly.

13. Remove four screws fastening Display assembly to front bezel.

14. Remove Display assembly.

15. Remove Display lens.

16. Insert new Display lens.

17. Insert new Display assembly. Fasten to front bezel with screws.

18. Fasten bracket to Display assembly with screw.

19. Fasten bracket to front bezel with screw.

20. Connect 10-conductor Keypad-to-Volume ribbon cable to Volume board

connector.

21. Tilt the front bezel back onto chassis. Refasten screws to each side of chassis.

22. Connect 10-conductor DSP-to-Keypad ribbon cable to DSP board connector J5.

23. Connect 20-conductor DSP-to-LCD Decoder ribbon cable to DSP board

connector J2.

24. Connect 8-conductor Inverter cable to DSP board connector J1.

25. Connect external display cable from J9 on the DSP/Display PWA.

Содержание Corometrics 250cx Series



























































































































































































































































Результаты поиска

Содержание Corometrics 250cx Series

Отзывы:

Похожие инструкции для Corometrics 250cx Series

Бренды по названию

Популярные бренды

GE Corometrics 250cx Series, Руководство по обслуживанию

Результаты поиска

Содержание Corometrics 250cx Series

Отзывы:

Похожие инструкции для Corometrics 250cx Series

Бренды по названию

Популярные бренды