GE Corometrics 250cx Series Скачать руководство пользователя | Manualshive

Страница: 147 / 252

background image

Revision C

250cx Series Maternal/Fetal Monitor

5-7

2036947-001

Troubleshooting: Diagnostic Control Screen

Run Time

This field displays the amount of time the monitor has been turned on—since the
field was cleared. The time is displayed in hours, minutes, and seconds. To clear this
field (reset the timer), activate the

Clear

softkey to the right of the run time field.

NOTE:

The

Clear

softkey also resets the recorder time field.

Recorder Time

This field displays the amount of time the recorder has been turned on (or printing in
maternal-only mode)—since the field was cleared. The time is displayed in hours,
minutes, and seconds. To clear this field (reset the timer), activate the

Clear

softkey

to the right of the recorder time field.

NOTE:

The

Clear

softkey also resets the monitor run time field.

Recorder Servicing

Removing the Strip Chart Recorder

Removing the strip chart recorder requires

loosening

the monitor’s front panel bezel.

Following this procedure carefully will avoid unnecessary damage to bezel’s
mounting screws and the unit’s front panel connectors.

1.

Turn off the 250cx Series Monitor and disconnect the power cord from the
monitor.

2.

Remove the nine screws which secure the monitor top cover. Four screws are
located on the bottom of the monitor and five screws are located in the back.

3.

Remove the cover by sliding it toward the rear of the monitor.

4.

Remove the four screws that attach the recorder bracket to the bottom of the
chassis.

5.

Remove the two screws which fasten the right and left sides of the bezel away
to the chassis.

6.

Disconnect the display ribbon cable from the DSP Board at J5.

7.

Disconnect the ribbon cable from the DSP Board.

8.

Disconnect the ribbon cable from the Recorder Board at J2. Leave the other end
connected to the Main Motherboard.

9.

Disconnect the Power Supply cable harness from the Recorder Board at J1.

10. Lift the recorder and its attached bracket out of the monitor.

Installing the Strip Chart Recorder

1.

Carefully place the recorder into the monitor housing and reassemble to the
chassis bottom with four screws.

2.

Re-connect the Power Supply cable harness to the Recorder Board at J1.

«
...
145
146
147
148
149
...
»

Содержание Corometrics 250cx Series





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Corometrics 250cx Series

Бренд: Taylor Made Страницы: 2

Бренд: York Fitness Страницы: 18

Бренд: Safco Страницы: 2

Бренд: Omni Страницы: 193

Бренд: 3M Страницы: 2

Бренд: Bante Instruments Страницы: 6

Бренд: Parker Страницы: 39

Бренд: G-Lab Страницы: 16

Бренд: G&G Страницы: 2

Бренд: olympia electronics Страницы: 2

Бренд: Analogue Solutions Страницы: 64

Power System KPS-US

Бренд: Keys Fitness Страницы: 8

Бренд: TBM Страницы: 22

Robus RVB007RGB10I65

Бренд: LED Group Страницы: 2

Бренд: Monosem Страницы: 52

WEIDER SHAPE GLIDER WECR43062

Бренд: ICON Health & Fitness Страницы: 6

Бренд: Duracell Страницы: 2

Бренд: DALBO Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды