GE Corometrics 250cx Series Скачать руководство пользователя

Страница: 132 / 252

4-52

250cx Series Maternal/Fetal Monitor

Revision C

2036947-001

Maintenance: Recorder Photosensor Calibration

Recorder Photosensor Calibration

Adjusting the Paper-Low Photosensor

Load paper in the recorder. Ensure that there are

black squares showing to

indicate a paper-low condition.

Press the

Record

button to turn on the recorder. Allow the paper to advance for

a few seconds in order to tension the paper.

Turn off the recorder.

Using a digital voltmeter, connect the positive lead to J9 (pin 4) on the Recorder
Board; connect the negative lead to J9 (pin 2).

Adjust R31 for a reading of +150 mVdc ± 2 mVdc on the digital voltmeter.

NOTE:

If you open and then close the recorder door, the reading may vary 5–10

mV, due to the loss of tension in the paper. This is acceptable and you do
not need to re-adjust.

Open the door and verify that the reading on the digital voltmeter is greater than
+4.75 Vdc.

Re-load the paper so that black squares show on the surface (i.e., the last several
sheets of a pack).

Turn on the recorder.

The value on the digital voltmeter should go up and down as the paper surface
alternates between black and white. Verify that the maximum value is greater
than or equal to 2.0 Vdc.

10. Turn off the recorder.

Adjusting the Paper-Out Photosensor

Load paper in the recorder. Ensure that there are

black squares showing to

indicate a paper-low condition.

Press the

Record

button to turn on the recorder. Allow the paper to advance for

a few seconds in order to tension the paper.

Turn off the recorder.

Using a digital voltmeter, connect the positive lead to J9 (pin 3) on the Recorder
Board; connect the negative lead to J9 (pin 2).

Adjust R29 for a reading of +150 mVdc ± 2 mVdc on the digital voltmeter.

NOTE:

If you open and then close the recorder door, the reading may vary 5–10

mV, due to the loss of tension in the paper. This is acceptable and you do
not need to re-adjust.

Open the door and verify that the reading on the digital voltmeter is greater than
+4.75 Vdc.

Turn off the recorder.

Содержание Corometrics 250cx Series



























































































































































































































































Результаты поиска

Содержание Corometrics 250cx Series

Отзывы:

Похожие инструкции для Corometrics 250cx Series

Бренды по названию

Популярные бренды

GE Corometrics 250cx Series, Руководство по обслуживанию

Результаты поиска

Содержание Corometrics 250cx Series

Отзывы:

Похожие инструкции для Corometrics 250cx Series

Бренды по названию

Популярные бренды