GE Corometrics 250cx Series Скачать руководство пользователя

Страница: 100 / 252

4-20

250cx Series Maternal/Fetal Monitor

Revision C

2036947-001

Maintenance: MECG Test

Insert the green plug of the FECG/MECG adapter cable, cat. no. (REF)
1442AAO, into the monitor’s

FECG/MECG

connector.

Connect the sub-cables of the other end of the simulator interconnect cable into
the color-coded connectors on the monitor/adapter:

ECG

, and

Turn

the Model 325 Simulator. Verify that the green

Power

indicator

illuminates.

Turn

the 250cx Series Monitor.

MECG Test

This portion of the functional checkout procedure ensures the integrity of the MECG
circuitry and the heart rate channel of the recorder.

Connect the simulator’s ECG cable to the

MECG

connector on the monitor

adapter cable (1442AAO).

Connect the simulator’s UA cable to the

connector on the monitor.

Set the switches on the Model 325 Input Simulator according to Table 2.

If not already on, depress the monitor’s

Record

button.

Turn the simulator’s

Manual Adjustment

knob counterclockwise and verify the

following on the monitor’s display until the monitor reads a value of 30 bpm:

The MHR/P mode is

MECG

The MHR heartbeat indicator (

) flashes at a rate of 30 times per minute.

The UA mode is

TOCO

Access the

Install Options Screen 2

and note the

Default TOCO Reference

value. Exit

the service mode by selecting

Restart

at the bottom of the screen.

After the monitor restarts, press the monitor’s front panel

UA Reference

button.

Verify the following on the monitor:

The UA value is referenced to the default value.

The recorder prints a continuous line at the default value on the bottom grid
of the strip chart paper.

The recorder prints the message

UA REF

on the strip chart paper.

Turn the simulator’s

Manual Adjustment

knob until the monitor displays an

MECG signal of approximately 60 bpm. Verify the following on the monitor:

The MHR value is 60 bpm.

The MHR heartbeat indicator (

) flashes at a rate of 60 times per minute

(1 per second).

The ECG “beep” volume can be heard from the rear panel speaker. The
volume can be adjusted on the MHR/P Setup screen.

Or using the

Volume

increase/decrease buttons, set

HR/PR Trace

in the

MHR/P Setup

screen The recorder should print a continuous line at 60 bpm

on the top grid of the strip chart paper.

Содержание Corometrics 250cx Series



























































































































































































































































Результаты поиска

Содержание Corometrics 250cx Series

Отзывы:

Похожие инструкции для Corometrics 250cx Series

Бренды по названию

Популярные бренды

GE Corometrics 250cx Series, Руководство по обслуживанию

Результаты поиска

Содержание Corometrics 250cx Series

Отзывы:

Похожие инструкции для Corometrics 250cx Series

Бренды по названию

Популярные бренды