GE auisys cs2 Скачать руководство пользователя страница 248 | Manualshive

Страница: 248 / 268

background image

Changing a cassette during a case

1.

Push the Agent quick key.

2.

Set agent delivery to off.

3.

Turn the lock on the handle to the vertical position (Aladin2
cassettes only).

4.

Remove cassette from the active bay.

•

Store the cassette in the cassette storage bay if it will not be
used.

•

Fill the cassette following the appropriate filling procedure if
the cassette requires filling.

5.

Install a cassette following the Installing a cassette procedure.
A tone sounds.
The agent setting in the quick key area flashes.
If cassette of same agent type is installed during a case, the last
agent setting used shows the agent quick key.

6.

Change or confirm the agent setting.

7.

To confirm the agent setting:

•

Push the ComWheel to confirm the setting.

•

Push the Agent quick key to confirm the setting.

If the setting is not confirmed within 30 seconds, the agent
delivery is set to off.

8.

To change an agent setting:

•

Turn the ComWheel to the desired setting.

•

Push the ComWheel or push the quick key to confirm the
setting.

Aisys CS²

13-6

2067226-001

«
...
246
247
248
249
250
...
»

Содержание auisys cs2













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для auisys cs2

Бренд: ZOLL Страницы: 84

Бренд: Kaivac Страницы: 29

Бренд: MacDon Страницы: 65

Бренд: Kapriol Страницы: 32

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 20

Бренд: GE Страницы: 212

Бренд: Mackie Страницы: 18

Бренд: Mackie Страницы: 2

Бренд: Mackie Страницы: 8

Бренд: Mackie Страницы: 7

MCX-C15 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 65

Бренд: Yamaha Страницы: 24

Бренд: Park House Healthcare Страницы: 32

VIMCO Sivoia SV-CCI-GRP

Бренд: Lutron Electronics Страницы: 2

Бренд: Atlas Metal Страницы: 2

Бренд: Hedson Страницы: 32

Бренд: JLG Страницы: 165

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды