GE ApexPro Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 218

GE ApexPro Скачать руководство пользователя страница 91

Managing patients

2001989-200E

ApexPro™

6-5

CAUTION

DELAY IN LEAD DETECTION— When using a 3-leadwire set,
there may be up to a 10 second delay in detection of the ECG
waveform. A

Leads Fail

or

No TELEM

alarm may be temporarily

displayed.

Wait for 10 seconds the ECG waveforms will be displayed.

CAUTION

When using the ApexPro transmitter with a 3-leadwire set, an RF
signal continues to be transmitted upon removal of ECG leadwires.
A

Leads Fail

alarm appears at the central station however the

system does not transition to a

No TELEM

alarm.

Please take appropriate measures as explained in this manual for the
leads fail condition.

If an SpO2 and/or NIBP device is connected to the transmitter, an
NIBP or SpO2 limit alarm with warning or advisory as configured
by the user will supersede the existing

Leads Fail

system warning

alarm.

When a 5-leadwire electrode configuration is not desirable, a 3-leadwire set can be
used. The following is a suggested configuration for a 3-leadwire electrode
placement:

370A, 373A

Right arm and left arm electrodes should be placed just below the right and left
clavicle.

Left leg electrode should be placed on a non-muscular surface on the lower edge of
the rib cage.

When using the standard 3-leadwire configuration, the following operating conditions
occur:

Lead Analysis

automatically switches to

Single-Lead

analysis. If an attempt is

made to change to

Multi-Lead

analysis, a message will appear briefly on the

monitor, indicating that

Multi-Lead

analysis is not possible, and no change will

occur.

R

L

F

RA

LA

LL

3-leadwire AHA Electrode Placement

3-leadwire IEC Electrode Placement

«
...
89
90
91
92
93
...
»

Содержание ApexPro



























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды