manualshive.com logo in svg

GE ApexPro, Руководство оператора

Поделиться
Скачать
GE ApexPro Скачать руководство пользователя страница 29

Introduction

2001989-200E

ApexPro™

1-17

Equipment compliance

IEC, UL, and EN 60601-1 device classification

This symbol indicates that the waste of electrical and electronic equipment must not be 
disposed as unsorted municipal waste and must be collected separately. Please contact an 
authorized representative of the manufacturer for information concerning the 
decommissioning of your equipment.

This symbol indicates the date of manufacture of this device. The first four digits identify the 
year and the last two digits identify the month.

Medical Equipment

With respect to electric shock, fire and mechanical hazards only in accordance with UL 
60601-1, CAN/CSA C22.2 NO. 601.1, IEC 60601-1, IEC 60601-1-1, IEC 60601-2-27 and IEC 
60601-2-49.

Manufacturer name and address.

European authorized representative.

2005-08

4P41

Type of protection against electrical shock

Transmitter — Internally powered

Receiver system — Class I

Degree of protection against electrical 
shock

ApexPro transmitter — Type CF Defibrillation proof applied part 

ApexPro CH transmitter — Type CF Defibrillation proof applied part 

Degree of protection against harmful 
ingress of water

ApexPro transmitter — IPX3 (IEC 60529)

1

ApexPro CH transmitter — IPX7 (IEC 60529)

2

Receiver system — Ordinary Equipment (enclosed equipment without protection against 
ingress of water)

Degree of safety of application in the 
presence of a flammable anesthetic 
mixture with air or with oxygen or nitrous 
oxide

Equipment not suitable for use in the presence of a flammable anesthetic mixture with air 
or with oxygen or nitrous oxide

Method(s) of sterilization or disinfection 
recommended by the manufacturer

Not applicable

Mode of operation

Continuous operation

1

The ApexPro transmitter is designed to be IPX3 compliant, so it can withstand inadvertent exposure to sprays. The transmitter should not be 

exposed to spray or shower during patient monitoring

2

The ApexPro CH transmitter is designed to be IPX7 compliant, so it can withstand inadvertent submersion. The transmitter should not be 

exposed to spray or shower during patient monitoring. 

Содержание ApexPro



























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды