manualshive.com logo in svg

GE AKTAprocess, Руководство по эксплуатации

Поделиться
Скачать
GE AKTAprocess Скачать руководство пользователя страница 66

Two columns

ÄKTAprocess can be configured to incorporate a second column. With this option, the
ÄKTAprocess can supply two columns, one after the other with mobile phase.

Sample pump

The sample pump allows sample to be injected into the column without the need to use
any of the system pumps for this purpose.

There are two optional inlets feeding the sample pump. The sample pump is also provided
with an extra pressure meter that protects the system against over pressure.

Extra pressure meter

An extra pressure meter can be installed after the column to accurately measure the
pressure drop over the column.

Extra pH meter

An extra pH-meter can be installed before the column on a gradient system to enable
the gradient to be monitored.

66

ÄKTAprocess Operating Instructions 29-0252-49 AA

3 System description

3.4 Optional components

Содержание AKTAprocess





















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды