GE akta start Скачать руководство пользователя страница 140

Страница: 140 / 214

Troubleshooting Flow chart 2

ERROR 102 UV Monitor Failure

1. Tighten Flow cell and flush it clean with

DM water.

2. Tighten connectors and remove any

strong direct light on the UV Monitor.

3. Tap Continue .

4. Go to Settings and service screen and

perform UV LED calibration.

Switch instrument Off, then On again.

1. Tighten and flush the Flow cell.

2. Clean the Flow cell; refer to

ÄKTA start

Operating Instructions.

3. Tap Continue on the error display.

Error message

still displayed?

Switch instrument Off, then On again.

Error message

still displayed?

1. Replace the Flow cell. Follow the Flow cell

replacement procedure.

2. Tap Continue on the error display.

1. Switch instrument Off.

2. Disassemble the UV Monitor.

3. Replace the UV Monitor and Flow cell.

4. Switch instrument On.

Perform UV LED

calibration

Proceed with your work.

Contact GE Service Engineer.

Note:
This Error message is displayed only
during switching on, as part of the power
on self test.

Yes

Error message

still displayed?

Error message

still displayed?

140

ÄKTA start Maintenance Manual 29-0603-08 AC

6 Troubleshooting

6.8 Troubleshooting flow charts

Содержание akta start























































































































































































































Результаты поиска

Содержание akta start

Отзывы:

Похожие инструкции для akta start

Бренды по названию

Популярные бренды

GE akta start, Руководство по обслуживанию

Результаты поиска

Содержание akta start

Отзывы:

Похожие инструкции для akta start

Бренды по названию

Популярные бренды