GE AKTA ready Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 227

GE AKTA ready Скачать руководство пользователя страница 30

2.4

Recycling information

Introduction

This section contains information about the decommisioning of ÄKTA ready.

Decontamination

The product must be decontaminated before decommissioning. All local regulations
must be followed with regard to scrapping of the equipment.

Disposal of the product

When taking the product out of service, the different materials must be separated and
recycled according to national and local environmental regulations.

Recycling of hazardous
substances

The product contains hazardous substances. Detailed information is available from your
GE Healthcare representative.

Disposal of electrical
components

Waste electrical and electronic equipment must not be disposed as unsorted municipal
waste and must be collected separately. Please contact an authorized representative
of the manufacturer for information concerning the decommissioning of the equipment.

30

ÄKTA ready Operating Instructions 28960345 AD

2 Safety instructions

2.4 Recycling information

«
...
28
29
30
31
32
...
»

Содержание AKTA ready




































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды