GE AKTA GO Скачать руководство пользователя страница 91

Страница: 91 / 117

7.1

Clean the instrument externally

CAUTION

Disconnect the power cord form the power outlet before cleaning
the instrument.

Maintenance interval

Clean the instrument externally when required. Do not allow spilled liquid to dry on the
instrument.

Required material

The following materials are required:

•

Cloth

•

Mild cleaning agent or 20% ethanol

Instruction

Follow the steps below to clean the instrument externally.

Action

Step

Turn off the instrument and disconnect the power cord from the wall socket.

Wipe the surface with a damp cloth. Wipe off stains using a mild cleaning
agent or 20% ethanol. Wipe off any excess.

Remove the top and bottom tray for cleaning. Put them back once they are
cleaned.

Let the instrument dry completely before using it.

ÄKTA go Operating Instructions 29360951 AC

7 Maintenance

7.1 Clean the instrument externally

Содержание AKTA GO






















































































































Результаты поиска

Содержание AKTA GO

Отзывы:

Похожие инструкции для AKTA GO

Бренды по названию

Популярные бренды

GE AKTA GO, Руководство по эксплуатации

Результаты поиска

Содержание AKTA GO

Отзывы:

Похожие инструкции для AKTA GO

Бренды по названию

Популярные бренды