GE AF-650 GP Series, Руководство по программированию

Страница: 120 / 175

3.19 LC-## Logic Controller
Parameter group related to programming the drive's built-
in Logic Controller. The Logic Controller consists of a series
of user defined actions (see
LC-52 Logic Controller Action )
that are executed when the corresponding user-defined
events are met.
3.19.1 LC-0# LC Settings
Parameters to configure the activation, deactivations and
reset of the Logic Controller (LC).
LC-00 Logic Controller Mode
Option: Function:
[0]
*
Off Disables the Logic Controller.
[1] On Enables the Logic Controller.
LC-01 Start Event
Select the boolean (TRUE or FALSE) input to activate Logic
Controller.
Option: Function:
[0]
*
False Select the boolean (TRUE or FALSE)
input to activate Logic Controller.
Enters the fixed value - FALSE
[1] True Enters the fixed value - TRUE.
[2] Running The motor is running.
[3] In range The motor is running within the
programmed current and speed
ranges set in H-70 Warning Current
Low to H-73 Warning Speed High .
[4] On reference The motor is running on reference.
[5] Torque limit The torque limit, set in F-40 Torque
Limiter (Driving) or F-41 Torque Limiter
(Braking) , has been exceeded.
[6] Current Limit The motor current limit, set in
F-43 Current Limit , has been
exceeded.
[7] Out of current
range
The motor current is outside the
range set in F-43 Current Limit .
[8] Below I low The motor current is lower than set
in H-70 Warning Current Low .
[9] Above I high The motor current is higher than set
in H-71 Warning Current High .
[10] Out of speed range The speed is outside the range set in
H-72 Warning Speed Low and
H-73 Warning Speed High .
[11] Below speed low The output speed is lower than the
setting in H-72 Warning Speed Low .
[12] Above speed high The output speed is higher than the
setting in H-73 Warning Speed High .
LC-01 Start Event
Select the boolean (TRUE or FALSE) input to activate Logic
Controller.
Option: Function:
[13] Out of feedb. range The feedback is outside the range set
in H-76 Warning Feedback Low and
H-77 Warning Feedback High .
[14] Below feedb. low The feedback is below the limit set in
H-76 Warning Feedback Low .
[15] Above feedb. high The feedback is above the limit set in
H-77 Warning Feedback High .
[16] Thermal warning The thermal warning turns on when
the temperature exceeds the limit in
the motor, the frequency converter,
the brake resistor or the thermistor.
[17] Line voltage out of
range
The mains voltage is outside the
specified voltage range.
[18] Reversing The output is high when the
frequency converter is running
counter clockwise (the logical product
of the status bits “running” AND
“reverse”).
[19] Warning A warning is active.
[20] Alarm (trip) A (trip) alarm is active.
[21] Alarm (trip lock) A (Trip lock) alarm is active.
[22] Comparator 0 Use the result of comparator 0.
[23] Comparator 1 Use the result of comparator 1.
[24] Comparator 2 Use the result of comparator 2.
[25] Comparator 3 Use the result of comparator 3.
[26] Logic rule 0 Use the result of logic rule 0.
[27] Logic rule 1 Use the result of logic rule 1.
[28] Logic rule 2 Use the result of logic rule 2.
[29] Logic rule 3 Use the result of logic rule 3.
[33] Digital input DI18 Use the result of digital input 18.
[34] Digital input DI19 Use the result of digital input 19.
[35] Digital input DI27 Use the result of digital input 27.
[36] Digital input DI29 Use the result of digital input 29.
[37] Digital input DI32 Use the result of digital input 32.
[38] Digital input DI33 Use the result of digital input 33.
[39] Start command A start command is issued.
[40] Drive stopped A stop command (Jog, Stop, Qstop,
Coast) is issued – and not from the
Logic Controller itself.
[41] Reset Trip A reset is issued
[42] Auto-reset Trip An Auto reset is performed.
[43] Ok key [OK] is pressed.
Parameter Descriptions AF-650 GP Programming Guide
DET-618C 119
3 3