Color Change
Foot Pedal
FOR HINGED TREE
1.
Carefully unpack, removing any bubble wrap and inspect the
contents of your tree.
{Fig. A}
You should have section A, B, & Top for 7.5’ tree,
or section A, B, C, & Top for 9’ tree.
Assembly Instructions
Thumbscrew
B
TREE ASSEMBLY DIAGRAM
TOP
A
B
4.
To change colors,
step on the color change
foot pedal to the desired
function as listed on the
back of the foot pedal.
GE Branded Christmas Trees
DISCLAIMER
:
DO NOT USE OR INSTALL ANY ADDITIONAL CHRISTMAS
LIGHTING OR ORNAMENTATION THAT IS POWERED BY A LIGHT BULB
SOCKET. DOING THIS MAY RESULT IN DAMAGE TO YOUR CHRISTMAS
TREE OR CAUSE PERSONAL INJURY. DOING THIS, WILL RESULT IN A
VOID OF THE LIMITED WARRANTY OF THIS PRODUCT.
GE is a trademark of General Electric Company
and is under license by Nicolas Holiday Inc.
Distributed by Nicolas Holiday Inc.,
For indoor use only
©2018 Nicolas Holiday Inc.,
9 F., No. 37, Guangfu North Rd.
Taipei, Taiwan 10560 All rights reserved.
THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.
Printed in China
HG18-DUAL
TOP
A
B
C
7.5’
9’
A
TOP
A
B
C
(FOR 9 FT TREES)
0218
Nicolas Holiday Inc. thanks you for purchasing this pre-lit
Christmas tree. Should you have any problems with your tree,
visit us at
www.geholidaylighting.com
for more information.
You can call our toll free number at 1-877-398-7337 .
Check our website for latest service hours and assembly
instruction videos.
The tree stand should be open and set at 90 angle.
Remember to tighten the thumbscrew after connecting
section A and tree stand. See
{Fig. B}
Untwist the
red
metal tie wrap holding
the branches in place. Gently position
any branches that do not fall into place.
2.
When you connect two tree
sections, it is important that you
align the mark on the tree poles.
See
{Fig. C}
Assemble section by section.
90
3.
To electrically connect the tree sections,
locate the male and female connector on
each section and fully insert the connectors
together.
Please fully screw on securing cap
Note
: Always unplug this product before
installing.
Do not plug in tree to a power outlet until
the entire tree is assembled.
SPARE PARTS:
Your tree includes a plastic bag containing spare LEDs.
9 FT TREES
B
A
TOP
B
C
A
TOP
7.5 FT TREES
IMPORTANT:
Store your carton neatly in a cool, dry location protected from
sunlight to prolong the tree life and to better keep the light sets in working order.
Do not place a heavy load on the carton to avoid damage to or crushing the carton
and tree inside.
TREE STORAGE
With proper storage, your Christmas tree will provide you years of use. Please keep
the original tree carton for proper storage. Disconnect all male and female connectors
between tree sections before
disassembling your tree,
place tree stand and tree sections
in original tree box as shown
below, then seal the carton
closed. Visit us at
www.geholidaylighting.com
for more repackaging information.
C
B
Male Connector
with Securing Cap
Female Connector
NOTE:
No tools required
Tree Sections Tree Stand
Approx. Asm Time
*
7 ft -9 ft
trees 3 or 4 Metal
10 – 15 minutes
* Does not include time for shaping branches, estimated shaping time is 30 minutes/section.
TROUBLESHOOTING TIPS
If one section of your tree does not illuminate, check that section for loose or missing
bulbs, all factory connections are properly made or that you properly made all the
electrical connections between each tree section.
8.25”x11.25”