GE Branded Christmas Trees
with Easy Shape Technology
®
allows tree branches to spring into shape
Easy Light Technology
®
eliminates cord connections
Just assemble and decorate!
TREE ASSEMBLY DIAGRAM
7.5 FT
COLOR CHANGE
FOOT PEDAL
TOP
B
A
TREE
STAND
Note:
Always unplug this product before installing.
Do not plug in, until entire tree assembled.
REMOTE CONTROL
OPEN
tree
top
tree stand
A B
Remove and unwrap all parts.
Retain shipping carton for repacking.
1
For proper installation and use, the
tree must be set up in a clear area
without any obstructions and on a
flat surface.
NOTE:
Before opening stand, be certain the
thumbscrew is loosened, so it does not
interfere with opening legs.
Place stand in desired location before
assembling. Your assembled tree will
be heavy and
difficult to move.
Open tree stand.
2
Insert section A into tree stand, after
first removing red protective cap.
Tighten screw to
secure section A
in the tree stand.
Untie RED twist-tie to release
branch panels.
Hint:
if your
branches do not fall
into place, DO NOT
force down. Gently
lift up on the branch
panels to release the
branch from its locked position. Now, all
rows of branches should be in the open
position.
Before adding the next section, follow the
shaping instructions listed below in
NOTE
.
NOTE:
For a natural uniform look, position
some branches
outward and
some upward.
Repeat for each
branch panel
and each
tree section.
3
NOTE:
Remove twist tie around looped
wires with plug adapter, extend wire and
set aside.
Assemble section B into section A.
Firmly seat both sections together.
4
Repeat step 3.
Hold tree top with one
hand as shown. Gently
pull down the outer
layer of branches, and
fully insert tree top
into the top of the
pole on section B.
5
Troubleshooting Tips
1.
If tree does not illuminate, try stepping on the
On/Off
FOOT PEDAL
. or use
REMOTE CONTROL.
If the tree is plugged into a switch controlled wall outlet,
make sure the switch is turned ON.
2.
If one section of your tree does not illuminate, check
that section for loose or missing LEDs, all factory connections
are properly made or that you properly made all the
electrical connections between each tree section.
3.
Also, check that connector on the main plug is fully
secured.
4.
All sections need to fully insert together align along
with the Indicated white marks.
To illuminate your tree, insert the
extension cord plug directly into an
electrical wall outlet.
Use remote conrtol or foot pedal
to select desired light function.
Color Change Function List:
STEADY
SLO-GLO
MULTI SLO-GLO
COLOR CHANGE
FLASHING
FLASH WHITE
MULTI FLASHING WHITE
AUTO FUNCTION
If needed, adjust
branch tips to make
the tree look fuller.
Congratulations!
Your tree is complete
and ready to
decorate.
6
6 colors
40 functions
6 colors
40 functions
TO TURN OFF
* Press foot pedal and
hold for 4 seconds.
TO TURN ON
* Press foot pedal to return to the
same function previously turned off.
Spare Parts:
Your tree includes a plastic bag containing
spare LEDs.
Distributed by Nicolas Holiday Inc.,
For indoor use only
©
2017 Nicolas Holiday Inc.,
9 F., No. 37, Guangfu North Rd.
Taipei, Taiwan 10560
All rights reserved.
THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.
Printed in China
17116LO
GE is a trademark of General Electric Company
and is under license by Nicolas Holiday Inc.
B
A
TOP
7.5 FT TREES
Most Frequently Asked Questions
Q. May I add a lighted, decorative tree topper to my tree?
A. Yes, But you would have to use separate extension
cord to power the tree topper.
Q. May I put blinking or flashing bulbs on my tree?
A. No
Q. May I add extra string sets to my pre-lit tree?
A. No
Q. May I put my pre-lit tree outside?
A. No. Pre-lit trees are for indoor use only.
Q. May I hang glass ornaments on a pre-lit tree?
A. Yes, however, do not hang directly on the wires
of the lights.
Q. May I remove a light string bulb and add a pig
tailed illuminated or animated ornament or motor?
A. No, removing the bulbs and inserting any additional
device into a lamp holder will cause the light set to
cease to operate and may revoke the limited
warranty of this product.
Disclaimer :
DO NOT USE OR INSTALL ANY ADDITIONAL
CHRISTMAS LIGHTING OR ORNAMENTATION THAT IS
POWERED BY A LIGHT BULB SOCKET. DOING THIS MAY
RESULT IN DAMAGE TO YOUR CHRISTMAS TREE OR CAUSE
PERSONAL INJURY. DOING THIS, WILL RESULT IN A VOID OF
THE LIMITED WARRANTY OF THIS PRODUCT.
Tree Storage
1.
Remove the tree’s main extension cord plug from
the wall outlet.
2.
Starting at the top, disconnect the top and section
B.
Step A:
Gently fold the branches up toward the center.
Care Should be taken to avoid damage to the lights.
3.
Disconnect sections B and A
4.
Refer to the drawing on how to repack your tree.
Important:
Store your carton neatly in a cool, dry location
protected from sunlight to prolong the tree life and to
better keep the light sets in working order. Do not place a
heavy load on the carton to avoid damage to or crushing
the carton and tree inside.
Nicolas Holiday Inc. thanks you for your purchase of this pre-lit
Christmas tree. With proper use and care, your Christmas tree
will provide years of use and memories.
Carefully follow the instructions below on how to assemble and
disassemble your pre-lit Christmas tree.
If you should have any problems with your tree, or if the tree
does not light after assembly, DO NOT return it to the place of
purchase. Please refer to the troubleshooting section of this
manual or call our toll free number: 1-877-398-7337 and a
customer support representative will assist you.
Our customer support center is open Monday through
Friday 10AM to 7PM EST with additional hours throughout
the holiday season:
Nov 11 to Dec 23:
Monday – Friday 8:00 am to 8:00 pm EST,
Saturday – Sunday 10:00 am to 7:00 pm EST
*Note: Schedule is subject to change at any time. Please check
back before contacting us for the most up-to-date schedule.
You may also visit us on the web at
www.geholidaylighting.com
Enjoy your holiday!
