GE Security CS575 страница 193 Скачать руководство пользователя | Manualshive

Страница: 193 / 209

background image

CS875-575-375-275-175 Installers Manual with CS5500 keypad

B.17.4

17.3 Glossary

Siren Tamper Restore

See Siren Tamper event message.

Start Download

The start of an up/download.

Start Prog

Start programming. The installer entered programming mode.

Tamper

A tamper.

Tamper Restore

See Tamper event message.

Telephone Fault

Telephone line faults.

Telephone Fault Restore

See Telephone Fault event message.

Trouble

A trouble condition.

Trouble Restore

See Trouble event message.

Walktest

The start/end of a walktest.

Zone Inactive Restore

See Zone Inactivity event message.

Zone Inactivity

A zone inactivity monitoring event.

Zone Lost

An RF transmitter has lost the supervision with the wireless receiver. This happens when the transmitter has not
reported its supervision message to the RF receiver within the long supervision window. See appendix 5.

Zone Lost Restore

See Zone Lost event message.

10 unsuccessful
download attempts

This is a security feature. This event occurs if someone tries to hack into the system.

Location

Term

Definition

17

Commands

A menu entry that groups options relating to issuing commands by the
installer.

17.1

Alarm Memory

A menu option that displays a list of alarms and where they occurred. Only the
alarms that have occurred during the last arm/disarm cycle are shown in the
alarm memory log.

17.2

Reset Smoke Detector

A menu command that resets two-wire and four-wire smoke detectors and the
Fire LED. For hardwired smoke detectors, the power supply to the smoke
detectors is cut temporarily.
RF smoke detectors have an auto reset because the RF communication is uni-
directional (from RF detector to RF receiver). This command does not reset RF
smoke detectors but should still be used to reset the Fire LED.

17.3

Service Check

A menu command that is used to verify service messages.
The service message disappears when the installer enters and then leaves
programming mode. If Master Code Resets Tamper Memory is enabled, a
master user can reset the service message by entering a master user code.

17.4

Do Self Test

A menu command that performs the keypad LED and LCD test and the
manual tests enabled in Diagnostics. The siren is activated during the tests if
the Manual Siren menu option is enabled. Likewise, a manual test call is made
to the central station if the Manual Dialler Test menu option is enabled.

Table 17-2: Event list

Event message

Explanation

«
...
191
192
193
194
195
...
»

Содержание CS575


















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CS575

Бренд: Caddx-Caddi Controls Страницы: 6

Бренд: Japan' Gold Страницы: 5

Бренд: JBL Страницы: 24

Бренд: Zircon Страницы: 2

Бренд: dallmeier Страницы: 2

Бренд: Uniden Страницы: 12

Бренд: Aurora Страницы: 2

Бренд: Bose Sicilia Страницы: 24

Бренд: Turbosound Страницы: 13

UAV-GA-T-2030TA

Бренд: Dahua Страницы: 17

Бренд: Pix Controller Страницы: 21

Бренд: Zuden Страницы: 19

Бренд: Idis Страницы: 40

Бренд: Magnavox Страницы: 24

Бренд: Interlogix Страницы: 8

ActivSoundBar TP-1866-UK

Бренд: promethean Страницы: 28

Бренд: SAKUTUS Страницы: 10

Jellyball FT12JB

Бренд: Fenton Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды