GE Security CS575 страница 192 Скачать руководство пользователя

Страница: 192 / 209

CS875-575-375-275-175 Installers Manual with CS5500 keypad

B.17.3

Fire Restore

See Fire event message.

First Open

The time at which the first area was opened.

Keypad Tamper

A keypad tamper.

Last Close

The time at which the last area was closed.

Late Close

A user disarmed the system after the closing time specified in the panel schedules.

Listen-in

The start of a listen-in session.

Log Full

The event log is full and the events must be reported to the up/download software. An event can also be sent to the
central station.

Low Batt Restore

See Low Battery event message.

Low Battery

The standby battery for the control panel/expansion module is low.

Mains Fail Restore

See Mains Failure event message.

Mains Failure

The 220 V has disappeared.

Manual Fire

A manual fire alarm generated by pressing the keys 1 and 3 on the keypad.

Manual Test

A manual test call to the central station.

Medical (Aux2)

A medical alarm generated by pressing the keys 4 and 6 on the keypad.

Open (disarm)

Opening (disarm) by a specific user.

Output

An output has been activated or restored. The output number is logged. This is linked to the output module number.

Output Restore

See Output event message.

Output Trip

An output has been activated.

Over-current

An excessive amount of current has been drawn from one of the outputs.

Over-current Restore

See Over-current event message.

PA Panic Alarm

A personal attack alarm has been tripped.

Panic Keypad

A panic alarm generated by pressing the keys 7 and 9 on the keypad.

Partarm

See Partial Arm event message.

Partial Arm

Part arm of the system by a specific user.

Recent Closing

An alarm occurred within five minutes of the panel being armed.

Re-exit

A special feature of false alarm preventing.

Reset

A user has manually reset a smoke detector.

RF Jam Restore

See RF Jammed event message.

RF Jammed

RF jamming.

RF Low Battery

An RF transmitter has reported a low battery.

RF Low Battery Restore

See RF Low Battery event message.

Service End

End of the ‘Installer on-site’ (service mode).

Service Start

Start of the ‘Installer on-site’ (service mode).

Silent Panic

A silent panic alarm.

Siren Tamper

A siren tamper.

Table 17-2: Event list

Event message

Explanation

Содержание CS575


















































































































































































































Результаты поиска

Содержание CS575

Отзывы:

Похожие инструкции для CS575

Бренды по названию

Популярные бренды

GE Security CS575, Руководство по установке

Результаты поиска

Содержание CS575

Отзывы:

Похожие инструкции для CS575

Бренды по названию

Популярные бренды