GE Multilin 469 Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 338

GE Multilin 469 Скачать руководство пользователя страница 152

5–10

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

CHAPTER 5: SETTINGS

protection or function timing in any way. It can be used to steady the display when
readings are bouncing.

•

MOTOR LOAD FILTER INTERVAL:

This value (when non-zero) averages current and

power factor for the programmed number of cycles using a running average
technique. This settings is intended for use on synchronous motors running at low
RPM and driving reciprocating loads. The number of cycles to average can be
determined by using current waveform capture. The number of cycles to complete
one stroke can be determined from this waveform. This value can be used as the
starting point for the motor load filter interval. Additional fine tuning may be required.
This settings is not seen if

NOMINAL SYSTEM FREQUENCY

is “Variable”.

This averaging may increase trip/alarm times by 16.7 ms for every cycle averaged.

5.2.3

Communications

Serial Communications

The following settings appear when the relay is ordered with the regular enhanced (E)
option.

PATH: SETTINGS

Z

S1 469 SETUP

ZV

COMMUNICATIONS

The 469 has three (3) serial communications ports supporting a subset of the Modbus
protocol (Refer to GEK-106491C:

469 Communications Guide)

. The front panel RS232 has a

fixed baud rate of 9600, a fixed data frame of 1 start, 8 data, and 1 stop bits with no parity.
The front port is for local use only and responds regardless of the slave address
programmed. This port may be connected to a personal computer running EnerVista 469
Setup. The software can download and upload settings files as well as upgrade the 469
firmware.

For RS485 communications, each 469 must have a unique address from 1 to 254. Address
0 is the broadcast address detected by all relays. Addresses do not have to be sequential
but no two units can have the same address or errors will occur. Generally, each unit
added to the link uses the next higher address starting at 1. Baud rates can be selected as
300, 1200, 2400, 4800, 9600, or 19200. The data frame is fixed at 1 start, 8 data, and 1 stop
bits, while parity is optional. The computer RS485 port is a general purpose port for

COMMUNICATIONS

[

SLAVE ADDRESS:

254

Range: 1 to 254 in steps of 1

MESSAGE

COMPUTER RS485

BAUD RATE: 9600

Range: 300, 1200, 2400, 4800, 9600,

19200

MESSAGE

COMPUTER RS485

PARITY: None

Range: None, Odd, Even

MESSAGE

AUXILIARY RS485

BAUD RATE: 9600

Range: 300, 1200, 2400, 4800, 9600,

19200

MESSAGE

AUXILIARY RS485

PARITY: None

Range: None, Odd, Even

«
...
150
151
152
153
154
...
»

Содержание 469



















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды