GE Multilin 469 Скачать руководство пользователя страница 150 | Manualshive

Страница: 150 / 338

GE Multilin 469 Скачать руководство пользователя страница 150

5–8

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

CHAPTER 5: SETTINGS

5.2

S1 469 Setup

5.2.1

Passcode

PATH: SETTINGS

Z

S1 469 SETUP

Z

PASSCODE

A passcode access security feature is provided in addition to the settings access jumper.
When shipped from the factory, the passcode is defaulted to 0. Passcode protection is
ignored when the passcode is 0. In this case, only the settings access jumper is required for
changing settings from the front panel. Passcodes are also ignored when programming
settings via the RS485 port. However when programming settings using the front RS232
port and the EnerVista 469 Setup software, a passcode is required (if enabled).

The

ENTER PASSCODE FOR ACCESS

settings is seen only if the passcode is not 0 and

SETTINGS ACCESS

is “Restricted”. The

SETTINGS ACCESS

and

CHANGE PASSWORD

settings are

seen only if the passcode is 0 and the

SETTINGS ACCESS

is “Permitted”.

To enable passcode protection on a new relay, follow the procedure below:

1. Press

MESSAGE

X

then

MESSAGE

T

until

CHANGE PASSCODE?

is displayed.

2. Select “Yes” and follow the directions to enter a new passcode 1 to 8 digits in

length.

3. Once a passcode (other than “0”) is programmed, it must be entered each time

settings access is restricted. If a non-zero passcode has been programmed and
settings access is restricted, then the

ENTER PASSCODE FOR ACCESS

message

appears when entering the

S1 469 SETUP

Z

PASSCODE

subgroup.

4. Enter the correct passcode. A flash message will advise if the code is incorrect

and allows a retry. If the passcode is correct and the settings access jumper is
installed, the

settings ACCESS: Permitted

message appears.

5. settings can now be entered. Press

ESCAPE

to exit the

S1 469 SETUP

Z

PASSCODE

group and program the appropriate settings. If no keys are pressed for 5 min-
utes, programming access will no longer be allowed and the passcode must be
re-entered. Removing the settings access jumper or setting the

SETTINGS ACCESS

settings to “Restricted” will also immediately disable settings access.

If a new passcode is required, gain settings access by entering the valid passcode as
described above, then press

MESSAGE

T

to display the

CHANGE PASSCODE

message

and follow directions. If an invalid passcode is entered, an encrypted passcode may be
viewed by pressing the

HELP

key. Consult the factory service department with this number

if the currently programmed passcode is unknown. Using a deciphering program, the
passcode can be determined.

PASSCODE

[

ENTER PASSCODE

FOR

Range: 1 to 8 numeric digits

MESSAGE

settings ACCESS:

Permitted

Range: Permitted, Restricted

MESSAGE

CHANGE PASSWORD:

No

Range: No, Yes

«
...
148
149
150
151
152
...
»

Содержание 469



















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды