GE Medical Systems MAC 1200 Скачать руководство пользователя страница 82

Страница: 82 / 180

5-22

MAC 1200

Revision B

2012250-022

Recording in 12 Lead Mode: Adjusting Measurement Points/QT Dispersion

Adjusting Measurement Points/QT Dispersion

This feature is only available with MAC 1200 units equipped with the
MEAS or DIAG option. The HEART interpretation program is also
required.

Global Measurement Points

After acquisition of an ECG in the 12 Lead mode, the global
measurement points for P onset, P offset, QRS onset, QRS offset, and
T offset can be adjusted manually.

After acquisition of the ECG, press

to display the screen for

verification of the global measurement point markers.

Verification of the Global Measurement Points

Description

Amplitude in [mV]

Selected lead

Active marker (large)

Inactive marker (small)

Time in [s]

1 mV

1 s

028A

Содержание MAC 1200





















































































































































































Результаты поиска

Содержание MAC 1200

Отзывы:

GE Medical Systems MAC 1200, Руководство оператора, Страница: 82 / 180

Результаты поиска

Содержание MAC 1200

Отзывы: