GE HEALTHCARE Monitor UV-900 Скачать руководство пользователя страница 8

Страница: 8 / 74

CE marking

The CE marking and the corresponding EU Declaration of Conformity is valid for the in-
strument when it is:

•

used according to the Operating Instructions or user manuals, and

•

used in the same state as it was delivered from GE, except for alterations described
in the Operating Instructions or user manuals.

1.3.2

Eurasian Customs Union

Introduction

This section contains additional regulatory information to comply with the Eurasian
Customs Union technical regulations.

Manufacturer and importer
information

The table below summarizes the manufacturer and importer information required by
the Eurasian Customs Union.

Information

Requirement

See Manufacturing information

Name and address of manufacturer

Telephone: + 46 771 400 600

Telephone number of manufacturer

GE Healthcare LLC

Importer and/or company for obtain-
ing information about importer

GE Healthcare Life Sciences

Presnenskaya nab., 10C, 12th floor

RU-123 317 Moscow, Russian Federation

Telephone 1: + 7 495 411 9714

Fax nr: + 7 495 739 6932

Email: [email protected]

Monitor UV-900 Operating Instructions 28962214 AD

1 Introduction

1.3 Regulatory information
1.3.1 EU Directives

Содержание Monitor UV-900











































































Результаты поиска

Содержание Monitor UV-900

Отзывы:

Похожие инструкции для Monitor UV-900

Бренды по названию

Популярные бренды

GE HEALTHCARE Monitor UV-900, Руководство по эксплуатации

Результаты поиска

Содержание Monitor UV-900

Отзывы:

Похожие инструкции для Monitor UV-900

Бренды по названию

Популярные бренды