GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 187

Страница: 187 / 240

Disassembly and reassembly

179

2062973-002

12.2 Module frame disassembly

12.2.1 Detaching the module frame front cover

A) Monitors with the E-module option

1. Press down the Module Frame release knob

and turn the Module Frame to a 90° angle, so
that the Module Frame faces to the front.

2. Release the two snaps on the top of the cover

unit:
- press (strongly) with your thumb on the

middle of the Module Frame cover unit's
front edge.

- pull out the front cover a little with the

other hand.

3. Release the four snaps in the inner side of the

E-module slot by pressing them (inwards) with
your finger. Release first the topmost two
snaps and then the lowest two snaps.

4. Detach the cover unit.

Содержание CARESCAPE Monitor B650

















































































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B650

Отзывы:

Бренды по названию

Популярные бренды

GE HEALTHCARE CARESCAPE Monitor B650, Техническое руководство

Результаты поиска

Содержание CARESCAPE Monitor B650

Отзывы:

Бренды по названию

Популярные бренды