Главная
/
GE HEALTHCARE
/
CARESCAPE Monitor B650
/
Техническое руководство

GE HEALTHCARE CARESCAPE Monitor B650, Техническое руководство

Поделиться

Страница: 166 / 240

GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 166

CARESCAPE Monitor B650

158

2062973-002

11.8 Problems and solutions

11.8.1

Start-up failures

Problem

Possible causes

Recommended actions

Failure to turn on the patient
monitor, when the following
conditions apply:
- The patient monitor is

connected to AC mains.

- The Mains voltage

indicator is not lit. (see
section

)

- None of the power

management LEDs are
lit.(see section

Unable to turn on the patient
monitor when it is powered
from the AC mains. Monitor
battery is not installed.

Power cord is loose.

Ensure that the power cord is connected properly
to the wall outlet and to the patient monitor.

Blown fuses.

Check the status of the fuses and replace them, if
necessary.
- Use only fuses with correct rating.
- If the fuses are blown repeatedly, investigate

the patient monitor carefully for possible short
circuits.

Power cord is faulty.

Check the power cord for wear and damage and
replace if necessary.

The power outlet does not
meet specified
requirements.

Check the power outlet being used:
- Refer to the patient monitor’s supplemental

information manual for power requirements.

- Check the power outlet being used, see section

The cable between the AC/
DC power supply unit and
the DC/DC board is loose
or faulty.

Check that the cable is intact and properly
connected to the AC/DC power supply unit and the
DC/DC board.
NOTE: You can easily check if the cable is properly
connected to the DC/DC board by detaching the
top cover.

The cable between AC/DC
power supply unit and AC
inlet is loose or faulty.

Check that the cable is intact and properly
connected to the AC/DC power supply unit and to
the AC inlet. Ensure the grounding connection is
good:
- Reconnect the cable, if loose.
- Replace the power supply unit, if the cable is

faulty.

The AC/DC power supply is
faulty.

Replace the AC/DC power supply unit.

The DC/DC board is faulty. Replace the DC/DC board.

«
...
164
165
166
167
168
...
»

Содержание CARESCAPE Monitor B650

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды