manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B650, Техническое руководство

Поделиться
Скачать
GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 131

 Theory of operation

  123

2062973-002

Touchscreen sensor

The models with touchscreen user interface include a resistive touchscreen sensor in the front 
of the LCD panel. The touchscreen sensor detects the presence and location of a touch within 
the display area and communicates the information to the touchscreen controller. 
In non-touchscreen models, the touchscreen sensor is replaced by an optical filter that has a 
scratch-resistant, non-glare surface coating.

Keypad

The patient monitor has a backlit keypad board with an on/standby button, 2 or 13 function 
keys and 3power indicator LEDs. 
The keypad is connected to the user interface board with a connector.

Trim Knob

The Trim Knob control is a rotary-switch with a push selection operation. The Trim Knob 
encoder detects the direction of the Trim Knob rotation and push button use and passes that 
information to the CPU board via the user interface board.

Alarm light board

The right hand side of the alarm light board contains red, yellow and blue LEDs to display 
different priority visual alarms. The left hand side of the alarm light board has blue LEDs for the 
silence alarm indicator light. 
The alarm light board also has a separate light sensor that is capable of measuring the 
ambient light intensity. The ambient light feedback can be used to auto-adjust the brightness 
of the keypad backlits, alarm light LEDs and the LCD display backlight to the different ambient 
light conditions.
The alarm light board is connected to the user interface board with the alarm light cable.

Speaker

The main speaker is used to provide audible alarms. The speaker cable is connected directly to 
the CPU board. The audio signal for the speaker is generated in the CPU board using a tone 
generator and an audio amplifier. Audio feedback controls the operation of the speaker.

Buzzer

The buzzer is connected to the user interface board. It functions as a back-up speaker and also 
provides an audible power loss alarm.

9.1.5 External Interfaces

Interface boards

There are two versions of the interface board: a Standard Interface Board and an Advanced 
Interface Board. 

Connector

Standard Interface Board Advanced Interface Board

USB 2.0 

2

4

DVI-I 1

1

Содержание CARESCAPE Monitor B650

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды