manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B650, Техническое руководство

Поделиться
Скачать
GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 122

CARESCAPE Monitor B650

 114

2062973-002

NOTE: Make sure that at least one other patient monitor is on the network. The other patient 
monitor must be in an admitted state and have an active ECG measurement with a simulator 
signal.

1.

Disconnect the network cable from the MC Network connector, if connected.

2.

Check that the wireless network symbol and the signal strength symbol are shown 

 

and that the signal strength is adequate.

 

3.

Select 

Data & Pages – Other Patients

  and select a patient from the list. 

 

4.

Select 

View

 and verify that a window with parameters from another patient displays on 

the left side of the screen. 

 

5.

Select 

Close View 

to close the window.

 

6.

Reconnect the MC Network cable back to the MC Network connector, if applicable.

8.3.11 IX printers

Perform the following test only if the patient monitor is connected to a printer in the IX Network 
and you did not print a test page while you configured the IX printer.
1.

Log in to Webmin.

2.

Select 

Configuration

 >

 Printers > Print Test Page

.

3.

Select the IX Printer to test.

4.

Select 

Save

.

5.

Verify that the test page was printed to the selected printer.

6.

Repeat steps 3 to 5 for all connected IX printers.

8.3.12 Insite with EXC

Perform the following test only if the remote service is configured and enabled.
•

Contact your local online support center to find out if they can view the patient monitor. 

8.3.13 Test completion

Discharge Patient 

or 

Reset Case 

to discard any changes made to the patient monitor 

configuration during checkout.

 

•

Complete the Appendix 

A. Installation check form

.

Содержание CARESCAPE Monitor B650

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды